manualshive.com logo in svg

Broadcom BCM1125, Руководство пользователя

Broadcom BCM1125 - высокопроизводительный процессор, обеспечивающий быструю и эффективную работу устройства. Чтобы ознакомиться с руководством пользователя, вы можете бесплатно скачать его с нашего сайта. Узнайте больше о вашем устройстве, загрузив руководство по эксплуатации на manualshive.com.

Поделиться
Скачать
background image

User Manual

BCM1250/BCM1125/BCM1125H

10/21/02

B r o a d c o m   C o r p o r a t i o n

Document

1250_1125-UM100CB-R

Section 7: DMA Page  

157

E

THERNET

 

AND

 S

ERIAL

 DMA E

NGINES

The Ethernet and serial DMA engines are identical except for using different per-packet options and status
flags. Each channel works as described above using either a ring or a chain. The DMA engines have the
restriction that neither the descriptors nor data buffers may be at an address serviced by I/O bridge 1, the
system behavior is UNDEFINED if this is violated. In practice this restriction just rules out DMA access from
the Ethernet or Serial DMA to the generic bus, since the other devices connected through I/O Bridge 1 are all
based on control registers and are unreasonable DMA targets. 

Figure 5 on page 9

 shows the devices that are

behind I/O Bridge 1.

Both Ethernet and serial DMA controllers are connected to the ZBbus through I/O Bridge 1. In the direction
from the ZBbus to the devices there is a separate command queue for read and writes to peripheral registers
and response queue for data returning to descriptor or buffer DMA read requests. This ensures that the DMA
traffic is not blocked by requests to slow peripherals (such as a slow device on the generic bus). In the direction
towards the ZBbus it is important that if a status read reports completion of a command the response does not
pass that command, so read and write requests from the DMA engine and responses to register reads are held
in a single queue. Generic bus responses do not need this ordering and are given their own return queue.

Each channel has an interrupt associated with it. In the ethernet interface the status for the two receive and
two transmit DMA channels are combined into the 

mac_status

 register for the interface (see

Table 182 on page 310

). The serial interface transmit and receive channel status are combined into the

ser_status

 register for each channel that can be read to determine the interrupt cause (see

Table 240 on page 357

). Reading the status will clear all bits in the status register and clear the interrupt. 

D

ESCRIPTOR

 C

OUNT

 W

ATERMARKS

The count of descriptors owned by the DMA controller is compared to two watermark registers. The high
watermark is set in the high_watermark field of the 

dma_config0

 register, and the low watermark is set in the

low_watermark field. It is expected that the high watermark is programmed to a larger value than the low
watermark. The CPU can opt to be interrupted when the descriptor count falls below either (or both)
watermarks. 

In a transmit engine setting the low watermark register to 1 and disabling the high watermark interrupt will give
an interrupt when all queued transmissions are complete. 

In a receive engine the interface can be configured to use automatic flow-control. If this is enabled then when
the number of descriptors falls below the low watermark the interface will be signalled to use flow control to
apply back pressure, which will only be removed when sufficient descriptors have been supplied to push the
count above the high watermark. If the engine is configured to interrupt the CPU when the descriptor count
falls below the high watermark, software has a chance to allocate more receive descriptors before flow control
is asserted. If automatic flow control is enabled and the high watermark is smaller than the low watermark the
behavior of the engine is UNPREDICTABLE. The watermark based flow control will not activate until after
buffers have been added to the descriptor queue for the first time, so the link will not be jammed as the interface
comes out of reset.

Содержание BCM1125





































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для BCM1125

PACOM Professional Series Quick Manual preview
Professional Series
Бренд: PACOM Страницы: 15
Acconeer A111 User Manual preview
A111
Бренд: Acconeer Страницы: 32
Magma PE6R4-I Quick Installation Manual preview
PE6R4-I
Бренд: Magma Страницы: 2
Lochinvar Armor 101 Series Instructions Manual preview
Armor 101 Series
Бренд: Lochinvar Страницы: 28
Lochinvar Armor 101 Series Service Manual preview
Armor 101 Series
Бренд: Lochinvar Страницы: 44
Analog Devices Linear SCP-LT8362-S-EVALZ Demo Manual preview
Linear SCP-LT8362-S-EVALZ
Бренд: Analog Devices Страницы: 8
Hama HDD Silenser Bedienungsanleitung preview
HDD Silenser
Бренд: Hama Страницы: 12
TP-Link VIGI NVR1008 Quick Installation Manual preview
VIGI NVR1008
Бренд: TP-Link Страницы: 2
ADC PG-FlexPlus AMU-912 Manual preview
PG-FlexPlus AMU-912
Бренд: ADC Страницы: 130
Fieldbus Specialists AT-FBUS Getting Started preview
AT-FBUS
Бренд: Fieldbus Specialists Страницы: 39
Dialogic DM/IP601-CPCI-100BT Quick Install Card preview
DM/IP601-CPCI-100BT
Бренд: Dialogic Страницы: 2
Hanwha Techwin Wisenet PRN-6400B4 Quick Manual preview
Wisenet PRN-6400B4
Бренд: Hanwha Techwin Страницы: 14
ZALMAN FS-V7 User Manual preview
FS-V7
Бренд: ZALMAN Страницы: 9
NXP Semiconductors UM10301 PCA8565 User Manual preview
UM10301 PCA8565
Бренд: NXP Semiconductors Страницы: 54
Unex EVK-351 Quick Start Manual preview
EVK-351
Бренд: Unex Страницы: 27
Xtreme SNMP-1PMINI User & Installation Manual preview
SNMP-1PMINI
Бренд: Xtreme Страницы: 83
Vacron VDH-NK300 Hardware Manual preview
VDH-NK300
Бренд: Vacron Страницы: 16
Comelit IPNVR016A User Manual preview
IPNVR016A
Бренд: Comelit Страницы: 140

Бренды по названию

Популярные бренды

Загрузить еще бренды