manualshive.com logo in svg

Broadcom BCM1125, Руководство пользователя

Broadcom BCM1125 - высокопроизводительный процессор, обеспечивающий быструю и эффективную работу устройства. Чтобы ознакомиться с руководством пользователя, вы можете бесплатно скачать его с нашего сайта. Узнайте больше о вашем устройстве, загрузив руководство по эксплуатации на manualshive.com.

Поделиться
Скачать
background image

BCM1250/BCM1125/BCM1125H

User Manual

10/21/02

B r o a d c o m   C o r p o r a t i o n

Page  

104

Section 6: DRAM

 Document

1250_1125-UM100CB-R

M

EMORY

 C

ONTROLLER

 A

RCHITECTURE

The memory controller consists of a ZBbus interface and one or two memory channel interfaces. The channels
on the BCM1250 are numbered 0 and 1, the BCM1125/H only has channel 1. The block diagram is shown in

Figure 14 on page 105

. 

The ZBbus interface consists of:

•

The request queue (RQQ).

•

A data buffer (DBF) for read and write.

•

The scheduler for issuing requests to memory (out-of-order).

The Request Queue (RQQ) is a 16 entry shift-register queue. Entries are added in-order as requests come
from ZBbus and are issued out-of-order to the memory channels. Any entry in the RQQ can be issued to
memory. Entries in the queue can be reserved for use by network DMA, this reduces the latency of reads and
improves performance when using slower or highly loaded memory systems.

The Data Buffer (DBF) is also 16 entry and is shared between reads and writes. Each entry in the buffer is a
full 256 bit block wide. The buffer has multiple pairs of read and write ports; one pair for ZBbus which can
transfer a full block each access, and a pair for each of the memory ports that transfer 64 bit double words.

When a request is received from ZBbus, entries are allocated in both the RQQ and the DBF. Entries are
normally added to the RQQ in sequential order. However, checks are first done to detect any write to read or
write to write address dependencies.

The RQQ holds the memory access information and initially the DBF is empty. If the request is a write then the
request is not ready for submission to the memory until the data has been received from ZBbus and written to
the DBF, at which time the RQQ entry becomes valid for the memory scheduler. Both entries are freed when
the write request is issued to the SDRAMs. If the request is a read the RQQ entry becomes valid as soon as
the L2 cache reports a miss, and the DBF entry is used to stage the data when it returns from memory. In this
case the entries are freed when the data is sent on ZBbus.

The memory controller calculates an ECC during writes, and will check it during reads. This provides correction
of all single bit errors and detection of double bit errors. An extra 8 bit ECC bus accompanies the 64 bit data
bus, matching the standard 72 bit DDR DIMMs. ECC checking can be disabled.

The memory controller will service uncacheable requests from ZBbus. A read-modify-write cycle for the full line
is needed for uncacheable writes, merging the new data into the existing block and recalculating the ECC. The
additional memory accesses and the poor utilization of the DBF will cause the memory system performance
to degrade if many uncacheable accesses are done.

Содержание BCM1125





































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для BCM1125

EAW MX8000 Technical Specifications preview
MX8000
Бренд: EAW Страницы: 2
NEC N8104-213 Installation Manual preview
N8104-213
Бренд: NEC Страницы: 10
NEC N8104-213 Instructions Manual preview
N8104-213
Бренд: NEC Страницы: 8
National Instruments NI 9426 Getting Started Manual preview
NI 9426
Бренд: National Instruments Страницы: 17
Telex Communications 2472AA Instruction Manual preview
2472AA
Бренд: Telex Communications Страницы: 28
Eaton SONiX Pm10 Technical Manual preview
SONiX Pm10
Бренд: Eaton Страницы: 14
Aurora EGO AE120 User Manual preview
EGO AE120
Бренд: Aurora Страницы: 6
Cypress Semiconductor CY7C1303BV25 Specification Sheet preview
CY7C1303BV25
Бренд: Cypress Semiconductor Страницы: 19
Adaptec Serial Attached SCSI (SAS) Expander Card Installation And User Manual preview
Serial Attached SCSI (SAS) Expander Card
Бренд: Adaptec Страницы: 26
IBM 7311-D11 Removal And Replacement Procedures preview
7311-D11
Бренд: IBM Страницы: 74
Wavtech bassFREQ Owner'S Manual preview
bassFREQ
Бренд: Wavtech Страницы: 8
Vertilon SIB064B User Manual preview
SIB064B
Бренд: Vertilon Страницы: 21
NI PXIe-1075 User Manual preview
PXIe-1075
Бренд: NI Страницы: 8
Idex KNIGHT MT-300 Instruction Manual preview
KNIGHT MT-300
Бренд: Idex Страницы: 4
Dell PowerEdge 2650 Service Manual preview
PowerEdge 2650
Бренд: Dell Страницы: 65
Extron electronics SMP 351 User Manual preview
SMP 351
Бренд: Extron electronics Страницы: 220
abaco systems PEX430 Hardware Reference Manual preview
PEX430
Бренд: abaco systems Страницы: 51
RadioLAN DockLINK User Manual preview
DockLINK
Бренд: RadioLAN Страницы: 118

Бренды по названию

Популярные бренды

Загрузить еще бренды