Introduction
Thank you for purchasing a BRIO™ Bluetooth headset. It’s designed for use with
Bluetooth enabled phones and provides comfortable and convenient wireless com-
munication. Included with the headset is an AC wall charger (QTC-BH150). The
instructions and information provided in this user manual apply to models BH-150i
and BH-150i-WH. Your BRIO headset offers the following features:
Power / Call Button
1.
Turns headset on / off.
■
Answers an incoming call when pressed briefly.
■
Ends a current call when pressed briefly.
■
Rejects an incoming call when pressed for just over 2 seconds.
■
Status LED (Blue) / Beeps
2.
Power On – LED illuminates for 1 second (along with 4 tones).
■
Power Off – LED illuminates for 1 second (along with 2 tones).
■
Ready For Pairing – LED flashes rapidly for about 2 minutes or until headset is
■
connected to a compatible phone. Headset changes to Idle if not paired within
2 minutes.
Idle – LED single flashes every 2.5 seconds when it is switched on, but not con-
■
nected to a phone.
Connection Active – LED double flashes every 8 seconds.
■
Incoming Call – LED flashes two times per second.
■
Call Ended – Single beep.
■
Low Battery – LED double flashes every 4 seconds and headset beeps every 5
■
seconds.
Charger Connection – For charging the headset’s internal battery.
3.
Headset Speaker – Directs caller’s voice into your ear. Removable speaker cover
4.
has 15 mm diameter.
Microphone – Picks up your voice during a call.
5.
Earhook – Attaches to headset below speaker. Position over / behind your ear to
6.
hold headset in place. See section Adjusting For Use On Either Ear.
Optional Speaker Cover – The extra speaker cover is 18 mm in diameter. This
7.
larger size cover can be used if the 15 mm cover (installed on headset at factory)
feels too loose in your ear.
Summary Of Audio / Visual Confirmations
Your BRIO headset provides audio / visual confirmations for actions or conditions as
listed below
Action / Condition
Status LED (Blue)
Headset Speaker
Headset is switched on (power
on)
Illuminates for 1 second
Four ascending tones
Headset is switched off (power
off)
Illuminates for 1 second
Two descending tones
Headset is switched on, but is not
paired or does not have an active
connection with a phone (idle)
Single flash blue every 2.5
seconds
N/A
Headset and phone are connected
(connection active)
Double flashes every 8 seconds
N/A
Headset is waiting to be paired
with a phone (ready for pairing)
Flashes rapidly for about 2
minutes
Four ascending tones fol-
lowed by two beeps when
first set for pairing
Incoming call
Flashes 2 times per second
Phone ring tone
Call in progress
Double flashes every 5 seconds
Caller’s voice
Call ended
N/A
Beeps once
Headset connected to charger and
charging not complete
Illuminates blue continuously
while battery is charging
N/A
Headset connected to charger and
charging complete
No illumination
N/A
Battery charge level is low
Double flashes every 4 seconds
Beeps once every 5
seconds
Charging The Internal Battery
Important: Before initial use, charge the internal battery for 2 hours. Only charge with
the QTC-BH150 supplied or other approved chargers. When fully charged, the battery
will provide up to 6 hours of talk time and 150 hours of standby time. For best battery
performance, use and store the headset at temperatures between 0º and 45º C (32º
and 113º F). The internal battery is not replaceable. The battery may be charged and
discharged hundreds of time, but will eventually wear out. Recycle the battery when it
no longer holds a charge. Do not dispose of headset or battery as household waste.
Connect the small end of the QTC-BH150 cable to the headset’s charger connec-
■
tion (see callout 3).
Plug the other end into a wall outlet (AC 120V / 220V). While the headset is
■
charging, the Status LED is continuously blue.
When the headset is fully charged, Status LED is off. Unplug the charger from
■
the headset and the wall outlet. Do not leave a fully charged battery connected
to the charger.
If the headset is connected to your phone, it will automatically disconnect once
■
the charger is connected to the headset. It is not possible to use the headset
while it’s charging.
Switching The Headset On / Off
To switch on, press and hold the Power / Call Button for 6 seconds. The headset
provides 4 ascending tones and the Status LED is solid blue for about 1 second.
To switch off, press and hold the Power / Call Button for 4 seconds. The headset
provides 2 descending tones and Status LED is solid blue for 1 second.
Pairing Headset To A Phone
Pairing is the process of linking your BRIO headset to a Bluetooth enabled phone. The
headset may be paired with up to 8 Bluetooth enabled phones, but used with only
one phone at a time. The pairing process must be completed with each phone you
want to use. Charge the headset’s internal battery, then follow these steps to pair the
headset to your phone:
Switch off the headset, but switch on your Bluetooth enabled phone. The headset
1.
must be within 30’ of the phone for pairing to be completed.
Press the Power / Call Button for about 10 seconds. When the Status LED begins
2.
to flash rapidly, release the button. Your headset is in pairing mode.
Activate the Bluetooth feature on your phone. Set the phone to search for Blu-
3.
etooth devices. See your phone’s user manual for more detailed instructions.
Select BRIO BH-150i (or BRIO BH-150i-WH) from the list of displayed devices.
4.
Enter pass code 0000 to pair and connect the headset to your phone. Note: Some
5.
phones pair first, then connect. See user manual for phone.
When connected, the Status LED double flashes blue every 8 seconds. The
6.
headset is now ready to be used with your phone.
6
1
3
4
BH-150i User Manual
2
5
7
Front
Back
