Brink Renovent Sky 200, Руководство по установке

Страница: 27 / 48

Renovent Sky 200 Rev. C 23
Fault
code
Cause Action appliance Action installer
E103
Bypass fault.
- None.
&XUUHQWWRRORZĺVWHSSHUPRWRUQRW
correctly connected or effective;
FXUUHQWWRRKLJKĺVKRUWFLUFXLWLQ
wiring or stepper motor)
‡ 7DNHWKHYROWDJHIURPWKHDSSOLDQFH
‡ &KHFNFRQQHFWLRQVWHSSHUPRWRU
replace wiring or stepper motor
E104
Extract fan defective.
- Both fans are switched off.
- Preheater is switched off.
- Postheater is switched off.
- Restart every 5 minutes.
‡ 7DNHWKHYROWDJHIURPWKHDSSOLDQFH
‡ 5HSODFHH[WUDFWIDQ
‡ %XWYROWDJHEDFNRQDSSOLDQFH)DXOW
will automatically be reset.
‡ &KHFNFDEOLQJ
E105
Supply fan defective.
- Both fans are switched off.
- Preheater is switched off.
- Postheater is switched off.
- Restart every 5 minutes.
‡ 7DNHWKHYROWDJHIURPWKHDSSOLDQFH
‡ 5HSODFH
‡ 3XWYROWDJHEDFNRQDSSOLDQFH)DXOW
will automatically be reset.
‡ &KHFNFDEOLQJ
E106
The temperature sensor
that measures the outdoor
temperature is defective. - Both fans are switched off.
- Preheater is switched off.
- Bypass closes and is blocked.
‡ 7DNHWKHYROWDJHIURPWKHDSSOLDQFH
‡ 5HSODFHWHPSHUDWXUHVHQVRU
‡ 3XWYROWDJHEDFNRQDSSOLDQFHIDXOW
will automatically be reset.
E107
The temperature sensor that
measures the temperature of
the extract air is defective
.
- Bypass closes and is blocked.
‡ 7DNHWKHYROWDJHIURPWKHDSSOLDQFH
‡ 5HSODFHLQGRRUWHPSHUDWXUH
sensor
E108
If present: The temperature
sensor that measures the
external temperature is
defective.
- If applicable: Postheater is switched off.
- If applicable: Geo heat exchanger is
switched off.
‡ 5HSODFHH[WHUQDOWHPSHUDWXUH
sensor
E109
Fault on connected CO
2
sen-
sor
- Appliance continues to operate
‡
Take the voltage from the appliance.
‡ 5HSODFH&2
2
-sensor; Correct setting
dipswitches of new CO
2
sensor
‡
Put voltage back on appliance; fault
is automatically reset.
E111
If present: The RH-sensor
that measures the huminity is
defective.
- Appliance continues to operate
‡
Take the voltage from the appliance.
‡
Replace RH-sensor.
Dip switches on control board
not set correctly.
- Appliance does nothing; red fault LED
on multiple switch is not activated
either.
‡ 3XWGLSVZLWFKHVLQFRUUHFWSRVLWLRQ
(see § 9).
Note!
If mode 2 of a multiple switch does not work, the modular connector of the multiple switch has been connected the wrong way round.
Cut off one of the RJ connectors to the multiple switch and mount a new connector the other way round.
Chapter 7 Fault
7.2 Display codes