manualshive.com logo in svg

Brightlink BLIP-A300TR-P-P, Руководство пользователя

Поделиться
Скачать
Brightlink BLIP-A300TR-P-P Скачать руководство пользователя страница 21

BRIGHTLINK 4K IP AV DISTRIBUTION

16 

5.5 Video Wall Routing Tab 

The tab "Video Wall" allows for a single source signal (TX) to be assigned to multiple 
Receiver (RX) units and displayed across multiple screens, appearing as a single video 
wall. The figure below illustrates the "Video Wall" routing tab inside the IPA Manager. 
The top portion is reserved for configuring and setting up the video wall, while the 
bottom half lists all available TX (Transmitter) and RX (Receiver) units. 

The video wall size can be adjusted by changing the number of rows and columns. The 
values for "bezel correction" represent the absolute amount of pixels. The default value 
is set to 16 pixels. Increase this value to adjust for thicker bezels while a value of zero 
would indicate no bezel correction at all is to be applied. 

Note: The source signal must be progressive scan. 

Содержание BLIP-A300TR-P-P




















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды