manualshive.com logo in svg

Brightlink BLIP-A300TR-P-P, Руководство пользователя

Поделиться
Скачать
Brightlink BLIP-A300TR-P-P Скачать руководство пользователя страница 18

BRIGHTLINK 4K IP AV DISTRIBUTION

13 

5.4 Video Routing Tab 

The "Video Routing" tab is used to manage signal routing between TX and RX devices. 
There are different video modes available: 

Genlock Mode 

This mode simulates a cable connection. When Genlock is selected, the output is a 
byte-by-byte replication of what was received from the source. 

The primary benefit is a very low (zero-frame) latency between source and displays. 
The display is genlocked to the source as if it is directly connected. 

In cases of the input video having a too large bandwidth to fit into a 10G network link 
(e. g. 4K @60Hz, 4:4:4) the video is slightly compressed to bring the stream down 
below the 10G limitation of the network. 

Fast Switch Mode 

Fast source switching, almost seamless to the human eye with about 1-2 frames 
transmission delay as well as output scaling of resolution and frame rate. 

Genlock Scaling Mode 

This mode combines the low latency and source locking benefits of the Genlock Mode 
with the output resolution (not frame rate) scaler found in the Fast Switch Mode. 

Содержание BLIP-A300TR-P-P




















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды