Brightlink BLIP-A300TR-P-P Скачать руководство пользователя страница 10

Страница: 10 / 51

BRIGHTLINK 4K IP AV DISTRIBUTION

3.2 IPA300/

BLIP-A300TR-P

-P Rear Panel

①

DC 12V:

DC port for AC power adapter connection.

②

HDMI IN:

Type-A female HDMI port to connect HDMI video source device.

③

HDMI OUT:

Type-A female HDMI port to connect HDMI display device.

④

10G LAN (PoE):

RJ45 port to connect directly to the RX or a network switch using

a CATx cable.

⑤

IR IN:

3.5mm jack to connect an IR receiver for IR routing control.

⑥

IR OUT:

3.5mm jack to connect an IR emitter for IR routing control.

⑦

RS232:

3-pin terminal block for RS232 routing control. Supports point to point

unicast and point to multipoint configuration.

⑧

AUDIO IN/OUT:

3.5mm jack to connect an audio source or output device.

⑨

ETHERNET:

RJ45 port to connect control devices (such as PC) for system control

via software and Ethernet pass-through.

Содержание BLIP-A300TR-P-P



















































Результаты поиска

Содержание BLIP-A300TR-P-P

Отзывы:

Бренды по названию

Популярные бренды

Brightlink BLIP-A300TR-P-P, Руководство пользователя

Результаты поиска

Содержание BLIP-A300TR-P-P

Отзывы:

Бренды по названию

Популярные бренды