Bridgeview BALE KING 5300 Series Скачать руководство пользователя

Страница: 14 / 105

Bridgeview Manufacturing Inc.

Cylinder Maintenance

The hydraulic cylinders are easily removed for repair or maintenance

simply by:

•

Lowering the fork (or deflector) to the down position and

unhooking the hydraulic lines. Be sure there is no pressure on the

lines and mark the line locations so there is no confusion when

reinstalling the cylinders. Check hydraulic schematics.

•

Removing the cotter pin closest to the frame of the machine and

sliding the cylinder pins out

•

To reinstall, reverse the removal procedure

NOTE: Always cover exposed cylinder shafts with grease to avoid rusting of shafts if the unit is

not used for extended periods of time. Rusted cylinder shafts are NOT covered by warranty

NOTE: Check all hoses and fittings periodically for leaks. Tighten or replace any dripping

components or any worn out hoses.

Implement Tongue

The adjustable hitch on the Bale King features a cast single

tongue with hammer strap insert. This allows for use with

tractors equipped with a hammer strap or with a single

drawbar. It also allows the machine to move independently

over rough terrain without bending the draw pin.

•

Make sure that the drawbar is set to

16 inches

behind

the PTO shaft for proper PTO length.

•

Adjust the hitch height to reduce the PTO angle as much as possible.

•

DO NOT install the insert if using a tractor with a hammer strap as this will bend the hitch

pin.

Содержание BALE KING 5300 Series










































































































Результаты поиска

Содержание BALE KING 5300 Series

Отзывы:

Похожие инструкции для BALE KING 5300 Series

Бренды по названию

Популярные бренды

Bridgeview BALE KING 5300 Series, Руководство оператора и каталог запасных частей

Результаты поиска

Содержание BALE KING 5300 Series

Отзывы:

Похожие инструкции для BALE KING 5300 Series

Бренды по названию

Популярные бренды