background image

Safety & Warranty Warnings

ATTENTION: READ THE FOLLOWING INFORMATION CAREFULLY BEFORE USING THIS PRODUCT

If unable to understand warnings, cautions, and/or instructions, contact the dealer or technical personnel if applicable, before attempting to 
use the equipment. Otherwise, injury or damage may result.
 

SAFETY WARNINGS:

• Do not use bed outdoors.
• Do not use bed near explosives.
• Using bed with oxygen administering equipment other than the
nasal masked type creates a possible fire hazard.
• When using nasal or masked type administering equipment, route and secure oxygen or air tubing properly to ensure that tubing does not 
become entangled or damaged during normal operation of the bed.
• Use caution when having liquids in or around the bed to ensure no spilling occurs. In case of spillage, stand in a dry,clean area of the floor 
and unplug the bed immediately. Clean up spill and allow the area around bed to dry thoroughly before using the electric controls again. Do 
not eat or drink hot liquids while operating the bed.
• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of 
experience and knowledge, unless they have been given supervision or instructions concerning   use of the appliance by a person 
responsible for their safety.
• Do not allow children or individuals with disabilities to operate the bed without adult supervision.
• Do not allow any person or pet under the bed at any time.
• During bed operation, make sure body is positioned within the confines of the bed. Do not place extremities over the sides of the bed 
when operating bed functions.

-1-

Содержание HOME Base II





























Отзывы: