Breas Clearway 2 Скачать руководство пользователя

Страница: 7 / 54

7 Maintenance Instructions

NIPPY Clearway 2 Service Manual

2210.2657 Rev 3.0

2 Maintenance Instructions

WARNING!

Clearway 2 must be:

•

Subjected to regular inspection and any applicable upgrades

in accordance with Breas Medical Ltd service instructions

•

Repaired in accordance with this technical manual, technical

bulletins and any special service instructions, by trained

service technicians

Deviation from these instructions may lead to risk of personal injury

Purpose

Carrying out regular inspection and preventative maintenance at the intervals
specified in this manual will ensure that the Clearway 2 will continue to
perform to specification during its service lifetime.

Introduction

Please read the safety precautions and ensure you have all the necessary

equipment, tools and parts available before attempting any maintenance

procedures.

Содержание Clearway 2























































Результаты поиска

Содержание Clearway 2

Отзывы:

Похожие инструкции для Clearway 2

Бренды по названию

Популярные бренды

Breas Clearway 2, Руководство по обслуживанию

Результаты поиска

Содержание Clearway 2

Отзывы:

Похожие инструкции для Clearway 2

Бренды по названию

Популярные бренды