manualshive.com logo in svg

Bray S70-130, Инструкция по установке, эксплуатации и обслуживанию

Поделиться
Скачать
Bray S70-130 Скачать руководство пользователя страница 27

SERIES 70 ELECTRIC ACTUATOR

Installation, Operation, and Maintenance Manual

27 of 48

© 2022 BRAY INTERNATIONAL, INC.  ALL RIGHTS RESERVED.  BRAY.COM  

The Information contained herein shall not be copied, transferred, conveyed, or displayed in any manner 

that would violate its proprietary nature without the express written permission of Bray International, Inc.

9.0  DISASSEMBLY AND ASSEMBLY

WARNING

Turn off all power and lockout/tag out service panel before installing or modifying 
any electrical wiring.

1 .  Disconnect external wiring from terminals .

2 .  Disconnect motor wires from the main terminal strip (motor neutral, open, and 

close)

NOTICE

Removal of switch plate with torque switches will void warranty.

3 .  To remove the switch plate:

a.  Follow after disconnecting external wires and motor wires.
b.  Unscrew the seven Phillips head mounting screws.
c.  Lift the switch plate(s) out as an assembly with the indicator shaft attached.
d. 

NOTE:

 Do not misplace shaft coupler, insert, or mounting screws.

Switchplate Fixed

Removable Switchplate 

Oldham Coupler

Figure 10. 

S70, Actuator Size E03, E06, E08 – switch plate removed.

Содержание S70-130

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды