background image

Page 36

33220

33220

W A R N I N G 

LIFT OPERATING 
INSTRUCTIONS

OPEN DOOR(S) AND SECURE 

TO UNFOLD PLATFORM: 

    Stand clear and press
    UNFOLD switch until
    platform stops (reaches
    floor level). 

Note: In event platform

      does not unfold, press
      FOLD switch to release
      Lift-Tite™ latches. 

TO UNLOAD PASSENGER: 

1. Load passenger onto
    platform and lock wheelchair
    brakes. 
2. Press     DOWN switch until
    entire platform reaches
    ground level and outer
    barrier unfolds fully. 
3. Unlock wheelchair brakes
    and unload passenger from
    platform. 

TO LOAD PASSENGER: 

1. Load passenger onto
    platform and lock wheelchair
    brakes. 
2. Press     UP switch to fold  
    outer barrier up and raise
    platform to floor level. 
3. Unlock wheelchair brakes
    and unload passenger from
    platform. 

TO FOLD PLATFORM: 

    Press      FOLD switch until
    platform stops.  Release
    switch. 

CLOSE DOOR(S) 

DOT — Public Use Lift 

30695

Whenever a wheelchair
passenger is on the platform,
the:
   • Passenger must be
     positioned fully inside
     yellow boundaries 
   • Wheelchair brakes must
     be locked 
   • Inner roll stop and outer
     barrier must be up 
Failure to follow these rules
may result in serious bodily
injury and/or property damage. 

• Read manual before operating
  lift. 
• Load and unload on level
  surface only. 
• Engage vehicle parking brake
  before operating lift. 
• Provide adequate clearance
  outside of vehicle to
  accommodate lift. 
• Do not operate lift if you
  suspect lift damage, wear or
  any abnormal condition. 
• Keep operator and bystanders
  clear of area in which lift
  operates. 

Replace missing, worn 
or illegible decals.  
Failure to do so may 
result in serious bodily 
injury and/or property 
damage.

WARNING

Decals and Antiskid

Decals

The lift is only as safe as 
the operator.  Replace any 
missing, worn or illegible 
decals!  Part numbers 
are provided for decals.  
Inspect your lift for missing, 
worn or illegible decals.  
Call 1-800-THE LIFT

®

    

for 

replacements.

21494

30695

Note:  Clean surfaces as 
detailed on page 38 before 
posting decals.

25675

WARNING

Lift installation and servicing prohibited by 
anyone who has not been certified by The Braun 
Corporation Sales and Service School.  Certified 
service technicians should call 1-800-THE LIFT 
to receive applicable installation/service manual.
Failure to follow this policy may result in serious 
bodily injury and/or property damage.

25675

21494

LIFT POWER

ON

OFF

OPERATING
INSTRUCTIONS

Read warnings and operate 
lift as outlined on LIFT 
OPERATING INSTRUCTIONS 
decal.  Lift operating 
instructions apply to wheelchair 
passengers and standees.

Standees:  Standees must 
stand at center of platform 
(fully inside yellow boundaries), 
grip handrails and lower head.

Interlocks:  Interlocks vary in 
type and operation.  Interlocks 
must be operational as defined 
in NHTSA Operations Checklist.

DOT — Public Use Lift

31045

31045

OPEN

CLOSE

MANUAL 
OPERATION

O

P

E

N

C

L

O

S

E

Using hand pump handle:

TO UNFOLD PLATFORM:

    1. Close hand pump valve 
        (turn clockwise).
    2. Insert handle in pump 
        and stroke until platform 
        folds fully (stops).
    3. Open hand pump valve 
        (turn counterclockwise) 
        until platform reaches 
        floor level.  Open 
        1/2 turn only. 
    4. Close hand 
        pump 
        valve (turn 
        clockwise).

DOWN (TO LOWER):

    Open hand pump valve (turn 
    counterclockwise).  Open 1/2 turn only.

UP (TO RAISE):

    1. Close hand pump valve 
        (turn clockwise).
    2. Insert handle in pump 
        and stroke platform 
        reaches floor level.

TO FOLD PLATFORM:

    Insert handle in 
    pump and stroke.

    Note:  Close valve 
    before operating 
    electric pump.

DOT — Public Use Lift

32940

32940

Содержание NCL Century 2 Series




























































Отзывы: