background image

LIOLS3_7/15

Brant Radiant Heaters, Ltd.

LS3 Series

 

Gas-Fired Infrared Tube Heater

!

WARNING

For Your Safety

If you smell gas:

 

•  Open windows.
•  Do not touch electrical switches.
•  Extinguish any open flame.
•  Immediately call your gas supplier from a
    neighbours phone.
•  Do not try to light any appliances. 

This heater must be installed and serviced by trained gas installation and service personnel only. 
Failure to comply could result in personal injury, asphyxiation, death, fire or property damage. 

Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any 
other appliance. In locations used for the storage of combustible materials, signs must be posted 
to specify the maximum permissible stacking height to maintain the required clearances from the 
heater to the combustibles. Signs must either be posted adjacent to the heater thermostats or in 
the absence of such thermostats, in a conspicuous location. 

Do not use this heater in indoor living or sleeping quarters, etc.! Installation of a tube heater 
system in residential indoor living spaces may result in property damage, serious injury, 
asphyxiation or death.

Consignes De Sécurité

Si vous sentez une odeur de gaz: 

•  Ouvrez les fenêtres.
•  Ne touches pas aux interrupters électriques.
•  Éteignez toute flamme nue.
•  Contactez immediatement votre compagnie de gaz.

WARNING: Improper installation, adjustment, alteration, service or maintenance 
can cause property damage, injury or death. Read the installation, operating and 
maintence instructions thoroughly before installing or servicing this equipment. 
AVERTISSEMENT. Une installation, un réglage, une modification, une réparation ou 
un entretien incorrect peut entraîner des dommages matériel, des blessures ou la 
mort. lisez attentivement les instructions d’installation, de fonctionnement et 
d’entretien avant de procéder à l’installation ou à l’entretien de cet équipement. 

INSTALLER: Present this manual to the end user. 

Keep these instructions in a clean and dry place for future reference.

Model#:

                                                                                            

Serial #: 

(located on rating label)

Ce dispositif de chauffage doit être installé et entretenu par installation à gaz formés et seul le personnel de 
service. Le non-respect de ces instructions peut entraîner des blessures corporelles, d’asphyxie, de décès, 
d’incendie ou de dommages matériels.

Ne pas stocker ni utiliser de l’essence ou d’autres vapeurs inflammables et liquides dans le voisinage de ce 
ou de tout autre appareil. Dans lieux utilisés pour le stockage de matériaux combustibles, les affiches doivent 
être posées pour spécifier la hauteur d’empilage maximale admissible à maintenir les autorisations 
nécessaires de l’appareil de chauffage aux combustibles. Les panneaux doivent être soit posté adjacent à la 
thermostats du réchauffeur ou en l’absence de telles les thermostats, en un endroit bien en vue.

Ne pas utiliser cet élément chauffant en indoor vivant ou lieux de couchage, etc.! Installation d’un système de 
chauffage tube dans des espaces de vie à l’intérieur d’une résidence peut entraîner des dommages matériels 
et des blessures graves, l’asphyxie ou la mort.

!

WARNING

Содержание LS3 Series

































































Отзывы: