Bradley Express SS-3N/BIR3/WH Скачать руководство пользователя

Страница: 10 / 15

SS-3N/BIR3/STD, SS-3N/BIR3/WH

Installation

9/7/2018

Bradley

• 215-1496 Rev. J; ECN 17-08-026

This valve is NOT factory preset. Upon installation, the temperature of this

valve must be checked and adjusted to ensure delivery of a safe water

temperature. Water in excess of 110°F (43°C) may cause scalding.

Adjust the Temperature

Loosen the cap screw about ¼"

(4–6 turns) and lift up the cover

(do not remove).

Using the cover, turn the

cartridge gently until desired

water temperature is reached. Do

not turn past stops as this may

damage the unit. Push the cover

down and tighten the screw.

Reinstall the valve bracket. Turn on the water supply to the Express and check for

leaks. Push the operating buttons of each station until all the air is purged from

the lines and water is flowing smoothly. Reinstall the access panel.

Содержание Express SS-3N/BIR3/WH
















Результаты поиска

Содержание Express SS-3N/BIR3/WH

Отзывы:

Похожие инструкции для Express SS-3N/BIR3/WH

Бренды по названию

Популярные бренды

Bradley Express SS-3N/BIR3/WH, Руководство по установке

Результаты поиска

Содержание Express SS-3N/BIR3/WH

Отзывы:

Похожие инструкции для Express SS-3N/BIR3/WH

Бренды по названию

Популярные бренды