background image

238-53506-00C REV 3/20 

 

 

 

HIGH EFFICIENCY COMMERCIAL GAS WATER HEATER 

INSTALLATION & OPERATION MANUAL 

WITH TROUBLESHOOTING GUIDE 

 

 

 
 

 
 

 

 

 

 
 

 

 

 
 
 

 

 

 
 
 
 
 
 

 

 

 
 
 
 
 
 
 
 
 
 
 
 
 

 

 

 

 

SAVE THESE INSTRUCTIONS AND KEEP FOR FUTURE REFERENCE

 

 

 
 
 
 
 
 
 

 
 

-

 

Do NOT store or use gasoline or other 
flammable vapors and liquids in the 
vicinity of this or any other appliance. 

 
-  

WHAT TO DO IF YOU SMELL GAS 

 

Do NOT try to light any appliance. 

 

Do NOT touch any electrical 
switch; Do NOT use any phone in 
your building. 

 

Immediately call your gas supplier 
from a neighbor’s phone.  Follow 
the gas supplier’s instructions. 

 

If you cannot reach your gas 
supplier, call the fire department. 

 

-

 

For customer comfort, safety, and 
convenience, it is recommended this 
water heater be installed and serviced 
by a plumbing professional. 

 

 

If the information in these 
instructions are not followed 
exactly, a fire or explosion may 
result causing property damage, 
personal injury, or death. 

 

WARNING

 

EF120T Model 

Содержание EF120T





























































Отзывы: