Bozzio Joysteer Generation 1.0 Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 56

Bozzio Joysteer Generation 1.0 Скачать руководство пользователя страница 36

Universal System Manual

Bozzio AG * joysteer®

page 36 of 56

6

Backup-battery

The backup-battery assures the required power for steer and brake, in the event of failure of
the power circuit of the vehicle.

The backup-battery will be tested via a pulse test.

Important:

The backup-battery is not included in the delivery pack of joysteer® (storage and safety
aspects).

Only the following types are to be used as backup-battery. Th

e Parameters “Capacity Low”

and “Capacity Insufficient” has to be set correctly depending on the choice made.

Type designation

Parameters

Opel Battery (12 Volt / 60 Ah)

Opel order # 12 01 003

or

GM order # 93 19 79 05

Capacity Low [mV]:

10’200

Capacity Insufficient [mV]:

10’000

Optima Yellow top YTS 4.2 (12 V /55Ah)

Capacity Low [mV]:

11’200

Capacity Insufficient [mV]:

10’900

No additional electrical consumers are to be connected to the backup-battery.

The positioning is vehicle specific. Refer to the vehicle specific manuals for details.

«
...
34
35
36
37
38
...
»

Содержание Joysteer Generation 1.0

























































Отзывы:

Нет отзывов