Bozzio Joysteer Generation 1.0 Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 56

Bozzio Joysteer Generation 1.0 Скачать руководство пользователя страница 35

Universal System Manual

Bozzio AG * joysteer®

page 35 of 56

5.10 MMI: Basic sensor unit brake

The basic sensor units are already described in the chapter “Handlebar”

5.11 MMI: Basic sensor unit gas

The basic sensor units are already described in the chapter “Handlebar”

5.12 Gas- / brake sensor adjustment

Important:

Never screw in the sensor while twisting the cable (Internal contacts may break). Always
screw by rotating the thread of the sensor. Always untwist the sensor cable before
plugging in X51-X54 on the cable harness.

1.

Put the MMI in 'max gas' position and adjust

X51 = 30

2.

Put the MMI in 'zero' position and adjust

X52 = X51 + 10

3.

Put the MMI in 'zero' position and adjust

X53 = X51

4.

Put the MMI in 'zero' position and adjust

X54 = X53 + 10

5.

Move the MMI from 'max gas' to 'max brake'. The different between X51 and X52
must always be smaller than 20.

6.

Move the MMI from 'max gas' to 'max brake'. The different between X53 and X54
must always be smaller than 20.

«
...
33
34
35
36
37
...
»

Содержание Joysteer Generation 1.0

























































Отзывы:

Нет отзывов