Bozzio Joysteer Generation 1.0 Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 56

Bozzio Joysteer Generation 1.0 Скачать руководство пользователя страница 14

Universal System Manual

Bozzio AG * joysteer®

page 14 of 56

4.5

Steering actuator module (SAM)

The steering actuator module is installed between the steering column and the steering
wheel. It is not required to dismantle the steering column.

The steering actuator module and its bracket is vehicle specific.

In all cases the steering lock has to be disabled or removed unless the customer uses the
original ignition lock / key.

Refer to the vehicle specific manual for installation instructions.

The installation is as following:

1. Ensure a straight-ahead wheel position

2. Dismantling of the steering wheel and the foot space cover following instructions of

the vehicle producer (attention airbag)

3. Mounting of the brackets (refer to vehicle specific manual)

Temporarily only tighten the screws by hand

4. Mounting of the steering actuator module (straight-ahead position)

The steering actuator module should not be rotated

Four complete rotations are possible; therefore the centre position is pre-set

The respective seal is only to be removed immediately prior to installation

5. Ensure all functionalities of the vehicles cable drums (Clock-Spring)

Indicators etc. remain

6. Remounting of the steering wheel

Tighten the screw according to the specification of the vehicle producer

7. Tighten the screws of the brackets with the indicated torque and secure with Loctite

243.

8. Install the airbag and the foot space cover according to the vehicle

producer’s

specifications

9. Check: the rotation of the steering wheel needs to be uniform and with low force

within the complete rotation range

«
...
12
13
14
15
16
...
»

Содержание Joysteer Generation 1.0

























































Отзывы:

Нет отзывов