Boss RC-600, Руководство по параметрам, Страница: 4 / 48

4
Memory Settings (LOOP)
Parameter Value
(Bold: default)
Explanation
INPUT
MIC 1, 2
OFF,
ON
Sets whether the sound from each input jack/connector and the rhythm should be inputted
to the track (ON) or not (OFF) during recording.
Turn the [1] knob to select the input jack/connector or RHYTHM, and press the [1] knob to
switch between ON/OFF.
* When STEREO LINK (p. 9) is “ON,” the MIC 1, 2 and L/R channels are shown as a single
connector.
INST1 L, R
INST2 L, R
RHYTHM
REC
Parameter Value
(Bold: default)
Explanation
REC ACTION
Specifies the order in which record/playback/overdubbing are switched when you press the [REC/PLAY] switch.
REC->DUB
Operation will switch in the order of Recording
0
Overdubbing
0
Playback.
REC->PLAY
Operation will switch in the order of Recording
0
Playback
0
Overdubbing.
QUANTIZE
With tracks for which LOOP SYNC (p. 3) is “ON,” under any of the conditions listed below, your timing will be corrected
(Loop Quantize) based on the tempo and time signature of the rhythm, even if the timing at which you press a switch is
slightly inaccurate.
5
If the rhythm is on
5
If there is an already-recorded track whose LOOP SYNC is turned on
5
If the MIDI Sync is on
* The QUANTIZE setting applies only during recording. It is ignored during overdubbing or playback.
* When you stop recording, it is quantized to match the measure length of the previously-recorded track (LOOP SYNC: ON)
or rhythm.
OFF
Recording begins the instant you perform the operation.
When you stop recording, it is quantized to match the measure.
MEASURE Quantize to the measure start location for recording.
AUTO REC
“AUTO REC” (auto record) starts recording when there is audio input from your guitar performance or the mic.
SW
OFF Recording will begin the instant you press the [REC/PLAY] switch.
ON
When you press the [REC/PLAY] switch, the REC/PLAY indicator will blink rapidly, and the
RC-600 will enter recording-standby mode.
When you begin playing, the REC/PLAY indicator will light and recording will start.
SENS 1–
50
–100
Specifies the input sensitivity at which auto record starts. Recording will start when the input
from the guitar or mic exceeds the specified sensitivity.
* This is valid when AUTO REC SW is “ON.”
BOUNCE SW OFF , ON Sets whether bounce recording is used (ON) or not (OFF).
BOUNCE TRACK
1–6
OFF,
ON
Specifies the track used for input during bounce recording (the track used for bouncing).
PLAY
Parameter Value
(Bold: default)
Explanation
S.TRK CHANGE
Specifies how the tracks will be switched when PLAY MODE (p. 2) is “SINGLE.”
IMMEDIATE
The change will occur immediately.
LOOP END The change will occur after playback has reached the end of the loop.
CURRENT TRACK TRACK1 –6 Sets the target track for operating and editing.
FADE TIME
IN
˜
,
˙
,
¸
,
ˇ
,
1MEAS–
2MEAS
–
64MEAS
Specifies the fade-in time as a number of measures when START MODE (p. 2) is set to “FADE.”
If you select a note, you can make the length shorter than a single measure.
OUT
Specifies the fade-out time as a number of measures when STOP MODE (p. 2) is set to “FADE.”
If you select a note, you can make the length shorter than a single measure.
ALL START TRK 1–6 OFF, ON
Set this to “ON” for tracks that should start playing when MIDI start data is received.
Use the [1]–[2] knobs to select the track, and press the [1]–[2] knobs to turn the setting on/off.
ALL STOP TRK
1–6 OFF, ON
Set this to “ON” for tracks that should stop playing when MIDI stop data is received.
Use the [3]–[4] knobs to select the track, and press the [3]–[4] knobs to turn the setting on/off.