background image

Safety

Improperly using and maintaining the equipment
can result in injury. To reduce the potential for
injury, comply with these safety instructions
and always pay attention to the safety-alert
symbol

, which means:

Caution

,

Warning

, or

Danger

—personal safety instruction. Failure to

comply with the instruction may result in personal
injury or death.

Preparation

Read the

Owner’s Manual

before operating or

servicing the spreader.

Ensure that only trained personnel installs and
performs maintenance on the equipment.

Always wear appropriate personal protective
equipment when loading, unloading, and servicing
the spreader. Wear substantial, slip-resistant
footwear, cold-weather clothing, hard hat, safety
glasses, and dust protection.

Many newer trucks are equipped with air bags.
Never disable, remove, or relocate any sensors or
other components related to the operation of the
air bags.

TGS 300 spreaders must only be used with a
minimum Class II receiver hitch. Do not exceed
the vehicle hitch rating.

The TGS 300 can hold a maximum weight of 91
kg (200 lb) of salt. Do not exceed this weight.

Operation

Read the

Owner’s Manual

before operating or

servicing the spreader.

Do not operate the machine while ill, tired, or
under the influence of alcohol or drugs.

For vehicle-mounted spreaders, always follow
the manufacturer’s recommendations for proper
parking procedures.

Always wear your seatbelt while operating a motor
vehicle.

Do not exceed 22.5 km/h (14 mph) while
spreading.

This spreader has an operating sound level below
70 dBA.

Never put any part of your body between the
spreader and the vehicle.

Overloading the spreader could result in
an accident or damage. Never exceed the
gross-vehicle-weight rating (GVWR) or the front
or rear gross-axle-weight ratings (FGAWR or
RGAWR) for the vehicle.

This spreader is restricted to the use of salt only.
Do not run other materials through the spreader.

Do not attempt to mount or remove the spreader
with material in it.

Turn the spreader off before filling, mounting,
removing, servicing, or cleaning it.

Never operate the spreader within 7.6 m (25 ft)
of bystanders.

Do not climb into or ride on the spreader.

Keep your hands, feet, and clothing away from
moving parts and mounting points.

Mount the spreader to a vehicle before loading
material.

Install ratchet straps and keep them properly
tightened with the slide-in attachment.

When transporting the spreader, ensure that it is
properly secured. Instructions are available at
www.bossplow.com.

The slide-in attachment must be fully engaged and
pinned into the vehicle’s 3 cm (1-1/4 inch) or 5 cm
(2 inch) receiver hitch.

Material safety data sheets (MSDS) are available
at www.bossplow.com.

Use a 1/2 ton minimum lifting device to move
heavy spreader components.

Do not store material in the hopper.

3

 

Содержание TGS 300













Отзывы: