background image

Safety

Improper use or maintenance by the operator or
owner can result in injury. To reduce the potential
for injury, comply with these safety instructions
and always pay attention to the safety-alert
symbol

, which means:

Caution

,

Warning

, or

Danger

—personal safety instruction. Failure to

comply with the instruction may result in personal
injury or death.

Preparation

Read the

Owner’s Manual

before operating or

servicing the plow.

Ensure that only trained personnel install and
perform maintenance on the equipment.

Keep your hands, feet, and clothing away from
moving parts and mounting points.

Ensure the plow is properly attached to the
machine before moving it.

Operation

When transporting the machine, position the plow
so as not to block your vision.

Do not

change the blade position when traveling.

Always lower the blade when the machine is not
in use.

Never

put any part of your body between the plow

and the machine.

Do not operate the machine while ill, tired, or
under the influence of alcohol or drugs.

Do not use the plow for any purpose other than
plowing snow.

Never

ride or lift persons on the plow.

Do not operate the plow on a steep incline.

Always

keep both hands on the handlebars while

operating the machine and plow.

Safety and Instructional Decals

Safety decals and instructions are easily visible to the operator and are located near any area
of potential danger. Replace any decal that is damaged or missing.

decalmsc23037

MSC23037

1.

Warning—read the

Owner’s Manual

.

5.

Warning—shut off the engine, remove the key, and read the

Owner’s Manual

before performing maintenance.

2.

Warning—all operators should be trained before operating
the machine.

6.

Crushing hazard—do not stand between the plow and vehicle
during maintenance.

3.

Warning—coupler must be locked before plowing.

7.

Warning—do not exceed 8 km/h (5 mph) when plowing.

4.

Warning—coupler must be unlocked to remove the plow.

8.

Warning—lower the plow when the vehicle is not in use.

3

 

Содержание MSC13960

















Отзывы: