Bose Personalized Amplification System страница 13 Скачать руководство пользователя | Manualshive

Страница: 13 / 50

background image

13

THEORY OF OPERATION

Table 2. Nominal and Peak Signal Levels

The minimum input level that would allow the system to reach full output (with all gain controls
all the way up) is -72 dBV. This is the output level of a Shure SM58 being exposed to about 78
dB SPL and should be sufficient for almost any application.

This gain scaling puts the main responsibility for the high-signal performance of the system on
the digital limiters. The limiters need to make sure that the output never exceeds 0dBV. The extra
6 dB headroom in the DSP can be used to compensate for gain variance in the power amp and
to allow the DSP to overdrive the power amps for very short periods of time. It may turn out,
that, for certain instruments, this will be required to achieve maximum SPL at acceptable sound
quality.

Point Nominal

Peak

Comment

Line In, Trim
@ Max

-30dBV un-

bal

- 12 dBV

Ch1 / Ch2 Vol. + Master @ 12:00. Maximum input
limited by input INA163 output clipping.

Line In, Trim
@ 12:00

-1dBV dBV

un-bal

+17 dBV

Ch1 / Ch2 Vol. + Master @ 12:00. Maximum input
limited by input INA163 output clipping.

Line In, Trim
@ min

+12dBV un-

bal

+18 dBV

Ch1 / Ch2 Vol. + Master @ 12:00. Maximum input
limited by input Buffer.

Mic., Trim @
max

-50 dBV

balanced

-32 dBV

balanced

This nominal = the output level of a Shure SM58
microphone that is exposed to 104 dBSPL.

Mic., Trim @
12:00

-21 dBV

balanced

-3 dBV

Balanced

Mic., Trim @
min

-8 dBV

balanced

+10dBV

balanced

This nominal = the output level of an AKG C4000
microphone that is exposed to 120 dBSPL.

Ch1, Ch2
Line out XLR

+6 dBV

balanced

+24 dBV

balanced

Dig. Vol.
Control, input

0 dBV

+18dBV

Dig. Vol.
Control,
output

-10 dBV

+18dBV

The nominal gain setting here is -10dB for the
volume c20 max out assumes Volume @
Max. (+10 max)

Insert Send

-10 dBV

+8dBV,

+18dBV

Peak @ 12:00 / Max Volume. Nominal is
conservative but should also work well for cheap
stomp boxes

Insert Return

-10 dBV

+6dBV

Assumes FX device in loop is set for unity gain
Peak limited by A/D input overload.

A/D input

-10 dBV

+4.5dBV

Assumes max voltage at the A/D = +6dBV=0dBFS,
D/A output filter gain = -1.5dB

D/A output

0 dBV

+4.5dBV

(debug)

0dBV

(normal)

The total excess gain in the DSP will be 16 dB, with
a nominal setting of +10dB. Again we assume
0dBFS = +6dBV. It is the responsibility of the digital
limiter to ensure that power amp does not clip, i.e.
that the output will not exceed 0 dBV

Bass Out

0 dBV

0/+4.5dBV
+6/10.5bal

Limiter engaged (normal operation) / Debug
Bass Out can be used Balanced / Un-balanced

Amp In

0 dBV

0 dBV

Nominal levels throughout the system are
referenced to full output power, so nominal & peak
are the same

Amp Out

30 dBV

30 dBV

This is maximum output at clip level ~250W
@ 4 ohms

«
...
11
12
13
14
15
...
»

Содержание Personalized Amplification System



















































Отзывы:

Нет отзывов

Похожие инструкции для Personalized Amplification System

Бренд: M2TECH Страницы: 17

Бренд: M-Audio Страницы: 8

trans-nova P4000

Бренд: Hafler Страницы: 2

Бренд: Harman Kardon Страницы: 9

Бренд: NAD Страницы: 2

Бренд: Inter-m Страницы: 10

Innovator L Series

Бренд: Axcera Страницы: 60

Бренд: AMC Страницы: 9

Бренд: Ltc Audio Страницы: 57

Бренд: Boston Acoustics Страницы: 8

Бренд: BRAX Страницы: 24

MOSCONI AS LED FRAMES

Бренд: Audio System Страницы: 2

Бренд: JDS Labs Страницы: 7

Бренд: Rainbow Страницы: 12

Бренд: JBL Страницы: 2

Livin Loud SX1250.1

Бренд: Kicker Страницы: 42

Бренд: Balanced Audio Technology Страницы: 14

MOON Evolution MC-8

Бренд: Simaudio Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды