background image

en

    Operating the appliance

24

Change the programme 

default settings

You can use or change the default 

settings for this washing cycle. 
To do this, repeatedly press the 

corresponding button until the required 

setting is displayed. 

Note:  

Pressing and holding the button 

automatically runs through the set 

values to the end. Then press the button 

once more and you can then change 

the setting values again.

The settings are activated without 

needing to be confirmed.
The settings are not saved after 

switching off the washing machine.
Default programme settings

~

 Page 20

Select additional programme 

settings

By selecting additional settings, you can 

better adapt the washing process to 

your items of laundry.
The settings can be selected or 

deselected depending on the 

programme progress. 
The button indicator lamps light up if a 

setting is activated.
The settings are not saved after 

switching off the washing machine.
Additional programme settings 

~

 Page 21

Start the programme

Press the 

A

 button. The indicator lamp 

lights up and the programme starts.
The display panel shows the "Ready in" 

time while the programme is running or 

the programme length and the 

programme progress symbols when the 

washing programme has started. 

Display panel 

~

 Page 11

Note:  

Foam detection

If the 

Å

 symbol also lights up in the 

display panel, the washing machine has 

detected too much foam during the 

wash programme and automatically 

activated additional rinse cycles to 

remove the foam.

Add less detergent to the next washing 

cycle with the same load.

If you want to lock the programme to 

prevent it from being inadvertently 

adjusted, you can select the childproof 

lock as follows.

Child lock 

(

E

 3 sec.)

You can lock the washing machine to 

prevent the functions you have set from 

being changed inadvertently. To do this, 

activate the childproof lock.
To 

activate/deactivate

, press and hold 

the 

Ready in -

 and 

+

 buttons at the 

same time for approx. three seconds. 

The 

E

 symbol is appears in the display 

panel.

E

 lights up: The childproof lock is 

active.

E

 flashes briefly: The childproof lock 

is active and the programme selector 

was turned or a button was pressed.

Note:  

The childproof lock remains 

active, even once the washing machine 

has been switched off. Before selecting 

the next programme, deactivate the 

childproof lock.

Содержание WAW32599SN

















































Отзывы: