Bosch SHP65TL5UC Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 82

Bosch SHP65TL5UC Скачать руководство пользователя страница 25

702_58300000170749_ara_en_c

Page 25 of 82

This material is intended for the sole use of BSH authorized persons and may contain confidential and proprietary
information. Any unauthorized review, use, copying, disclosure, or distribution in any format is prohibited.

4.8

Water switch

Mounted underneath sumps, water switches consist of a motor-
operated disk with seven holes, which rotates under three sump
ports (upper / lower spray arms, top sprinkler) to provide precise
water control.

Water switch disks do

not

rotate

continually, but

counterclockwise (ccw) based on the wash program and water
clarity (i.e. directed by the control and aqua sensor).  When water
is clear, the water switch directs water to the upper or lower spray
arm.  When water is dirty, the switch directs water to both spray
arms.

Motor ratings: 110 – 127 VAC, 60 Hz, synchronous, 4.8 RPM
(ccw), class E insulation.

4.9

Info Light (selected models)

A

red

or

blue

light

(LED)

shines on the floor to show the

dishwasher is running. The door shouldn’t be opened until the
light has gone out, showing the dishwasher wash cycle has
completed.

Info lights can’t be seen from the side – the
only light seen is a warm glow on the floor.

1.  Disk
2.  Housing
3.  Seal (to sump)
4.  Pulse generator
5.  Drive motor
6.  Gear with cam
7.  Gear with shaft

3

4

7

6

5

1

2

1.  To lower spray arm
2.  To upper spray arm
3.  To top sprinkler

1

2

3

To both

spray arms /

top sprinkler

To lower

spray arm

To upper

spray arm /

top sprinkler

To upper

spray arm

Water shown directed

to both spray arms /

top sprinkler

«
...
23
24
25
26
27
...
»

Содержание SHP65TL5UC



















































































Отзывы:

Нет отзывов