Bosch SHP65TL5UC Скачать руководство пользователя страница 12

Страница: 12 / 82

702_58300000170749_ara_en_c

Page 12 of 82

This material is intended for the sole use of BSH authorized persons and may contain confidential and proprietary
information. Any unauthorized review, use, copying, disclosure, or distribution in any format is prohibited.

The

Delicate

option can be chosen only with

Heavy

Auto

and

Normal

cycles. It’s best used for lightly soiled items.

TIP

: The dishwasher automatically defaults to

Auto

when

turned off and back on. If the

Sanitize

option was used in

the last cycle, the dishwasher will default to

Auto

with the

Sanitize

option selected.

The

Extra Shine

option can be chosen with any wash cycle

except

Rinse

. It raises the rinse temperature and extends the

drying time to further enhance drying.

3.3

Resetting the dishwasher

To reset the dishwasher or cancel a wash cycle, press and hold
the

Start

button for about three (3) seconds until

the

display

shows “

0:01

”. Close the door and wait about one minute for the

dishwasher to stop draining and for the display to show “

0:00

”.

Turn the dishwasher off (by pressing the

On / Off

button) after it

stops draining.

3.4

Interrupting a cycle

interrupt

a wash cycle, press the

On / Off

button to turn the

dishwasher off. To resume the wash cycle, press the

On / Off

button again to turn the dishwasher on.

3.5

Changing basic settings

Intensive Drying

feature can be turned on or off,

End of Cycle

Tones can be changed and

rinse-aid dosage

can be changed

using dishwasher controls.

NOTE

: For SHP / SHX / SHV models with hidden controls,

the door must be opened before changing settings and
closed after changing settings.

3.5.1

Intensive Drying (“Extra Dry”)

Intensive Drying

provides a higher temperature during the final

rinse to improve drying. It may cause a slightly longer running
time.

Press the

On / Off

button to turn the dishwasher on. While

pressing and holding the “

” button

(below)

, press and hold the

Start

button until the display shows “

d:00

”. Release both buttons.

Press the “

” button

(above)

to turn

Intensive Drying

on or off

(“

d:01

” =

and “

d:00

” =

Off

). Press the

Start

button to save the

setting.

Содержание SHP65TL5UC



















































































Результаты поиска

Содержание SHP65TL5UC

Отзывы:

Похожие инструкции для SHP65TL5UC

Бренды по названию

Популярные бренды

Bosch SHP65TL5UC, Инструкции по ремонту

Результаты поиска

Содержание SHP65TL5UC

Отзывы:

Похожие инструкции для SHP65TL5UC

Бренды по названию

Популярные бренды