Bosch Rexroth VFC 3210 Скачать руководство пользователя страница 180

Страница: 180 / 282

Stall overcurrent prevention
This function is used to prevent the frequency converter from overcurrent when

the load is excessively heavy or the acceleration time is excessively short. This

function is always active during acceleration or at constant speed.

Code

Name

Setting range

Default

Min.

Attri.

C0.27 Stall overcurrent prevention level

20.0 %…[C2.42]

150.0

0.1

Stop

The typical behavior of stall overcurrent during acceleration is shown as the fig-

ure below:

Fig. 12-43: Stall overcurrent during acceleration

●

[Output current] > [C0.27]
The output frequency stops increasing.

●

[Output current] < [C0.27]
The output frequency resumes increasing to the setting frequency with de-

fined acceleration time.

The typical behavior of stall overcurrent at constant speed is shown as the figure

below:

Bosch Rexroth AG
Functions and Parameters

VFC 3210

152/253

DOK-RCON04-VFC3210****-IT01-EN-P

Содержание Rexroth VFC 3210



























































































































































































































































































Результаты поиска

Содержание Rexroth VFC 3210

Отзывы:

Bosch Rexroth VFC 3210, Руководство по эксплуатации, Страница: 180 / 282

Результаты поиска

Содержание Rexroth VFC 3210

Отзывы: