Bosch Rexroth VFC 3210 Скачать руководство пользователя страница 168

Страница: 168 / 282

12.9.2 Selecting the Reference and Feedback

Before using PID control function make sure [E1.00]…[E1.04] ≠ '41: PID deacti-

vation'.
Take the following steps to configure the PID reference:

Step 1: Select the PID reference channel

Code

Name

Setting range

Default

Min.

Attri.

E4.00 PID reference channel

0...10

–

Stop

E4.03 PID engineering analog reference

0.00...10.00

0.00

0.01

Run

E4.04 PID engineering speed reference

0...30,000 rpm

Run

●

[E4.00] = 0: Inactive
The PID control function is inactive.

●

[E4.00] = 1: Panel potentiometer
The reference value is set by adjusting the potentiometer on the operating

panel.

●

[E4.00] = 2: Panel button
The reference value is set by E0.07 'Digital setting frequency', which can be

decreased or increased by pressing the <▼> or <▲> buttons on the operating

panel respectively when the frequency converter is running.

●

[E4.00] = 3: AI1 analog input
The reference value is set by AI1 analog input.

●

[E4.00] = 7: Communication
The reference value is set by engineering software, PLC or other external devi-

ces via Modbus or other communication.

●

[E4.00] = 8: Analog reference E4.03
The reference value is set by parameter E4.03.

●

[E4.00] = 9: Speed reference E4.04
The reference value is set by parameter E4.04.

Step 2: Select the PID feedback channel

Code

Name

Setting range

Default

Min.

Attri.

E4.01 PID feedback channel

AI1 analog input

–

Stop

●

0: AI1 analog input
Feedback value is set by AI1 analog input.

Any of analog inputs can ONLY be assigned with one function.

Bosch Rexroth AG
Functions and Parameters

VFC 3210

140/253

DOK-RCON04-VFC3210****-IT01-EN-P

Содержание Rexroth VFC 3210



























































































































































































































































































Результаты поиска

Содержание Rexroth VFC 3210

Отзывы:

Bosch Rexroth VFC 3210, Руководство по эксплуатации, Страница: 168 / 282

Результаты поиска

Содержание Rexroth VFC 3210

Отзывы: