Bosch Rexroth VFC 3210 Скачать руководство пользователя страница 167

Страница: 167 / 282

12.9 PID Control

12.9.1 Function Description

PID control is used in process controls such as flow control, pressure control,

temperature control, and in control of other engineering values. In PID control, a

negative feedback system is formed with proportional, integral and derivative

operations based on the differences between reference values and their feed-

back. In this way, the difference between the actual output and the reference is

reduced.
The basic control principle is shown as the figure below:

Fig. 12-37: PID control principle

VFC 3210

Bosch Rexroth AG

Functions and Parameters

DOK-RCON04-VFC3210****-IT01-EN-P

139/253

Содержание Rexroth VFC 3210



























































































































































































































































































Результаты поиска

Содержание Rexroth VFC 3210

Отзывы:

Bosch Rexroth VFC 3210, Руководство по эксплуатации, Страница: 167 / 282

Результаты поиска

Содержание Rexroth VFC 3210

Отзывы: