manualshive.com logo in svg

Bosch Rexroth VFC 3210, Руководство по эксплуатации, Страница: 152 / 282

Поделиться
Скачать
Bosch Rexroth VFC 3210 Скачать руководство пользователя страница 152

2-wire control mode 2 (Forward / reverse, run / stop)
Step 1: Activate 2-wire control mode 2
Set [E1.15] = '1: Forward / reverse, run / stop'.
Step 2: Define two digital inputs

●

Set one of digital inputs as '35: Forward running (FWD)'

●

Set one of digital inputs as '36: Reverse running (REV)'

Example:
Connected switch K1 to X1, and set [E1.00] = '35: Forward running (FWD)'.
Connected switch K2 to X2, and set [E1.01] = '36: Reverse running (REV)'.

Fig.  12-27:   2-wire control mode 2

The control logic is shown in the table below:

K1

K2

Running status

Open

Open

Stop

Closed

Open

Running forward

Open

Closed

Stop

Closed

Closed

Running reverse

Tab.  12-8:   2-wire control mode 2 configuration

Bosch Rexroth AG
Functions and Parameters

 VFC 3210

124/253

DOK-RCON04-VFC3210****-IT01-EN-P

Содержание Rexroth VFC 3210



























































































































































































































































































Отзывы:

Нет отзывов