manualshive.com logo in svg

Bosch Rexroth VFC 3210, Руководство по эксплуатации, Страница: 140 / 282

Поделиться
Скачать
Bosch Rexroth VFC 3210 Скачать руководство пользователя страница 140

DC-braking before start

DC-braking is used in applications, in which regular deceleration to

stop or a quick stop is required. The larger DC-braking current, the

larger braking force. However, the withstanding capability of the mo-

tor has to be considered before use the DC-braking function.

'DC-braking before start' is used in applications where the load may encounter

forward / reverse rotation when the frequency converter is in stop mode.

Code

Name

Setting range

Default

Min.

Attri.

E0.38 Start DC-braking time

0.0...20.0 s

0.0

0.1

Stop

E0.39 Start DC-braking current

①

0.0...150.0 %

0.0

0.1

Stop

①

: percentage of frequency converter rated current.

Fig.  12-20:   DC-braking before start

When  [E0.38]  ≠  0,  DC-braking  will  be  executed.  After  this,  the  frequency  con-

verter starting to accelerate to [E0.36] 'Start frequency' for a period of [E0.37],

then accelerate to the setting frequency.

Bosch Rexroth AG
Functions and Parameters

 VFC 3210

112/253

DOK-RCON04-VFC3210****-IT01-EN-P

Содержание Rexroth VFC 3210



























































































































































































































































































Отзывы:

Нет отзывов