manualshive.com logo in svg

Bosch Rexroth VFC 3210, Руководство по эксплуатации, Страница: 116 / 282

Поделиться
Скачать
Bosch Rexroth VFC 3210 Скачать руководство пользователя страница 116

12.3.2  Fan Maintenance Reminder

This  function  is  used  to  remind  users  maintaining  the  cooling  fan  in  time.  The

maintenance time can be set according to the actual application conditions.

Code

Name

Setting range

Default

Min.

Attri.

C0.51 Fan total running time

0...65,535 h

0

1

Read

C0.52 Fan maintenance time

0...65,535 h

0

1

Stop

C0.53 Fan total running time reset

0: Inactive
1: Active

0

–

Run

To use this function, take the following steps:
Step 1: Set the maintenance time of the fan properly
Set parameter C0.52 'Fan maintenance time' according to the actual application

conditions.

Step 2: Observe the fan lifetime status at warning
When a warning code 'FLE' (Fan maintenance period expired) is displayed on the

operating  panel,  [C0.51]  'Fan  total  running  time'  is  higher  than  [C0.52]  'Fan

maintenance time'.

●

Pause the display of the warning code 'FLE' by pressing the <Func> button.

●

Perform fan maintenance or replacement.

Step 3: Reset the fan lifetime counter after fan maintenance or replacement

●

Set parameter C0.53 'Fan total running time reset' to '1: Active'
After the execution, [C0.53] and [C0.51] will be reset to '0' automatically. By

now, the warning code 'FLE' is cleared completely.

●

Adjust the value of C0.52 'Fan maintenance time' if necessary

Bosch Rexroth AG
Functions and Parameters

 VFC 3210

88/253

DOK-RCON04-VFC3210****-IT01-EN-P

Содержание Rexroth VFC 3210



























































































































































































































































































Отзывы:

Нет отзывов