Bosch Rexroth VFC 3210 Скачать руководство пользователя страница 115

Страница: 115 / 282

12.3 Power Stage Configuration

12.3.1 Carrier Frequency Setting

Code

Name

Setting range

Default

Min.

Attri.

C0.05 Carrier frequency

2...12 kHz

Run

C0.06 Carrier frequency auto-

matic adjustment

0: Inactive
1: Active
2: Fixed carrier frequency

–

Stop

When output frequency is less than 5 Hz, the carrier frequency is 2

kHz; When output frequency is 5...10 Hz, the carrier frequency is 4

kHz; When output frequency is more than 10 Hz, the carrier frequen-

cy is the same as customer's setting.

For derating figures related to carrier frequency, see

chapter 6.2.2 "Derating of

Electric Data" on page 23

To achieve optimized performance, the carrier frequency setting

should follow the equation: [C0.05] ≥ 10 x [E0.08].

With [C0.06] = 1, the carrier frequency can also be changed automatically to

keep the power module temperature within the normal range.
With [C0.06] = 2, the carrier frequency is always fixed to C0.05.

VFC 3210

Bosch Rexroth AG

Functions and Parameters

DOK-RCON04-VFC3210****-IT01-EN-P

87/253

Содержание Rexroth VFC 3210



























































































































































































































































































Результаты поиска

Содержание Rexroth VFC 3210

Отзывы:

Bosch Rexroth VFC 3210, Руководство по эксплуатации, Страница: 115 / 282

Результаты поиска

Содержание Rexroth VFC 3210

Отзывы: