Bosch Rexroth Sytronix FcP 5020 Скачать руководство пользователя страница 83

Страница: 83 / 88

10 Diagnosis

10.1 Warning Code

Panel

display

Function

code

Error information

Reason

Solution

APF1

d0.88

0: No warning

1: Pressure feed-

back exceed limit

1. Excessive pressure setting
2. Pressure transducer failure

1. Set pressure to a lower value
2. Check if the wiring is proper-

ly connected for pressure feed-

back transmission

2: Pressure com-

mand exceed limit

Pressure command upon us-

er’s input exceeding [F4.22] Set pressure to a lower value

3: Flow command

exceed limit

Flow command upon user’s

input exceeding [F4.24]

Set flow to a lower value

4: Oil filter warn-

ing

Oil filter almost full

Clean or replace filter

5: Oil level warn-

ing

Oil level too low

Refill oil

6: Oil temperature

warning

Oil temperature reached

Reduce hydraulic loses or en-

hance oil cooling

7: Oil change

warning

Operation time exceeds oil

life time

Change oil and reset operation

timer (F4.54)

8: (Reserved)

9: Pump thermal

protection warn-

ing

Pump speed is lower than re-

quired for pump cooling

(F4.36)

Increase system minimum

speed

10: Pump power

limitation warning

Required pump power ex-

ceeds limitation set in F4.35 Adjust limitation or system load

11: Oxygen too

high

Oxygen feedback is higher

than F4.72

Check the value of oxygen feed-

back via AI or F4.72, F4.73

12: System pres-

sure too low

Pressure feedback is lower

than F4.74

Check the value of pressure

feedback via AI or F4.74,

F4.75

Tab. 10-1: Warning code

FcP 5020

Bosch Rexroth AG

Diagnosis

DOK-RCON03-FCP5020****-QU04-EN-P

79/83

Содержание Rexroth Sytronix FcP 5020

























































































Результаты поиска

Содержание Rexroth Sytronix FcP 5020

Отзывы:

Похожие инструкции для Rexroth Sytronix FcP 5020

Бренды по названию

Популярные бренды

Bosch Rexroth Sytronix FcP 5020, Быстрый старт

Результаты поиска

Содержание Rexroth Sytronix FcP 5020

Отзывы:

Похожие инструкции для Rexroth Sytronix FcP 5020

Бренды по названию

Популярные бренды