Bosch Rexroth Sytronix FcP 5020 Скачать руководство пользователя страница 65

Страница: 65 / 88

7.12.3 myCro Function Description

●

Drive enables via both digital input and analog input together
The drive can be started only if both digital and analog input are available: For

digital input, select one of them to "22: Enable for myCro" by setting one of

F2.16...F2.24 = 22, and connect this DI terminal to switch. Also EFC run com-

mand source must be set to "panel" by setting E0.01 = 0, for example, to

make this function possible. For analog input, the feedback of oxygen sensor

will be monitored via the input channel that has been selected (by setting one

of F2.00...F2.02 to "4: Oxygen feedback (for myCro)"), and the drive can be

started only if the feedback is higher than F4.70, or can be stopped only if the

feedback is lower than F4.71.

●

Speed variable pump with constant pressure control
For myCro function, the pump needs to be accelerated rapidly to N_min, and

then accelerated slowly until the pressure command is archived.
myCro default setting is loaded by setting F1.20 = 4. The parameters are

F3.12, F3.13, F3.16, F3.32, F3.33 and F3.36.

●

myCro specialized warning and error message
Warning 1 : oxygen too high
Converter raises warning message if oxygen feedback is higher than [F4.72]

for [F4.73] hours. Warning index will be shown via displaying parameter d0.88

= 11, and this also set a high signal to a DO or relay, depending on which of

F2.36...F2.38 has been set to 4.
This warning is working only if F1.20 = 4, no matter that converter is in stand-

by or operation.
Warning 2 : pressure too low
Converter raises warning message if the pressure feedback is lower than

[F4.74] bar for [F4.75] s.
Warning index will be shown via displaying parameter (also for fieldbus)

d0.88 = 12, and this also set a high signal to a DO or relay, depending on

which of F2.36…F2.38 has been set to 5.
This warning is working only if F1.20 = 4, and converter is in operation.
Error : pressure too high
Converter raises error if pressure feedback is higher than [F4.16] bar for

[F4.18] s. For more information, please see

chapter 7.10.3 "Actual Pressure

Monitoring" on page 48

Actual pressure monitoring, which is a FcP general function, will be active, if

control bit2 of F4.00 has been set to 1. Not as other myCro warning control-

led by F1.20.

FcP 5020

Bosch Rexroth AG

Block Diagram of Main Functions

DOK-RCON03-FCP5020****-QU04-EN-P

61/83

Содержание Rexroth Sytronix FcP 5020

























































































Результаты поиска

Содержание Rexroth Sytronix FcP 5020

Отзывы:

Похожие инструкции для Rexroth Sytronix FcP 5020

Бренды по названию

Популярные бренды

Bosch Rexroth Sytronix FcP 5020, Быстрый старт

Результаты поиска

Содержание Rexroth Sytronix FcP 5020

Отзывы:

Похожие инструкции для Rexroth Sytronix FcP 5020

Бренды по названию

Популярные бренды