Bosch Rexroth RE 90300-B Скачать руководство пользователя страница 53 | Manualshive

Страница: 53 / 64

background image

RE 90300-B/2021-01-19, Bosch Rexroth AG

Troubleshooting |

Axial piston units

53

/64

14.2 Axial piston pump malfunction table

Table 9: Axial piston pump malfunction table

Malfunction

Possible cause

Remedy

Unusual noises

Insufficient air bleeding of the hydraulic
system

Fill the axial piston unit, suction line for the
hydraulic pump and the reservoir
Completely air bleed the axial piston unit and
hydraulic system
Check correct installation position

Insufficient suction conditions,
e.g. insufficient dimensioning of the suction
line, viscosity of the hydraulic fluid too high,
suction height too high, suction pressure
too low, foreign particles in the suction line,
impermissible or contaminated filters in the
suction line

Machine/system manufacturer: Check the
system, e.g. optimize inlet conditions,
use suitable hydraulic fluid
Fill the suction line with hydraulic fluid

Remove foreign particles from the suction line

If necessary, check the filter system and replace
the filter

Drive speed too high

Machine/system manufacturer: Reduce drive speed

Wrong direction of rotation

Machine/system manufacturer: Check correct
direction of rotation, see chapter 1.1.10
"Preparation" on page 32

Improper mounting of the axial piston unit

Check the mounting of the axial piston unit
according to the specifications of the machine/
system manufacturer – observe tightening torques

Improper mounting of assembled parts,
hydraulic lines or improper installation of
the coupling

Fasten assembled parts according to the
parameters provided by the coupling fitting
manufacturer

Valve and controller vibrate

Optimize the adjustment of the controller of the
axial piston unit and the pressure limitation in the
hydraulic system
Air bleed the axial piston unit and hydraulic system

Contact Bosch Rexroth Service:
Optimize the setting of the pressure limitation and
pressure control valve

Mechanical damage to the axial piston unit
(e.g. bearing damage)

Replace axial piston unit

Contact Bosch Rexroth Service

Increased, unusual vibration

Bearings worn

Contact Bosch Rexroth Service

«
...
51
52
53
54
55
...
»

Содержание Rexroth RE 90300-B

































































Отзывы:

Нет отзывов

Похожие инструкции для Rexroth RE 90300-B

Бренд: NARGESA Страницы: 33

Бренд: Panasonic Страницы: 9

Бренд: TAIKO Audio Страницы: 24

Бренд: AcceleDent Страницы: 3

Бренд: Zero 88 Страницы: 32

Бренд: BACtrack Страницы: 16

Бренд: Ibiza Страницы: 21

Бренд: IBASE Technology Страницы: 67

Бренд: IBC Страницы: 8

Бренд: Ibanez Страницы: 8

Бренд: IAI Страницы: 5

Бренд: IEMCA Страницы: 82

KID 80-IV Touch

Бренд: IEMCA Страницы: 122

Бренд: Calrec Страницы: 92

Бренд: H&S Страницы: 42

Бренд: Parkside Страницы: 95

Бренд: Yamaha Страницы: 4

Бренд: Wacker Neuson Страницы: 120

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды