Bosch Rexroth MSK030-NSNN Series Скачать руководство пользователя страница 41

Страница: 41 / 48

●

Type plate specifications of the affected products, in particular type codes

and serial numbers

●

Your contact data (phone and fax number as well as your e-mail address)

4 Appendix

4.1 EU Declaration of conformity

According to ATEX directive 2014/34/EU, the manufacturer,
Bosch Rexroth AG
Bgm.-Dr.-Nebel-Str. 2
97816 Lohr a. Main / Germany
declares that the following products

3~ PM-Motor

MSK030...-NSNN

MSK040...-NSNN

MSK050...-NSNN
MSK050...-RSNN

MSK060...-NSNN
MSK060...-RSNN

MSK061...-NSNN
MSK061...-RSNN

MSK070...-NSNN
MSK070...-RSNN

MSK071...-NSNN
MSK071...-RSNN

MSK076...-NSNN
MSK076...-RSNN

MSK100...-NSNN
MSK100...-RSNN

MSK101...-NSNN
MSK101...-RSNN

Trade name: Rexroth
from the date of manufacture 2021-07-01 were developed, designed and manu-

factured in compliance with the above-mentioned directive.
The sole responsibility for drawing up this declaration of conformity lies with the

manufacturer.
Applied harmonized standards:

Standard

Title

Edition

EN 60079-0

(IEC 60079-0)

Explosive atmospheres - Part 0: Equipment –

General requirements

2018 (2017)

EN 60079-15

(IEC 60079-15)

Explosive atmospheres - Part 15: Equipment

protection by type of protection “n”

2010 (2010)

EN 60079-31

(IEC 60079-31)

Explosive atmospheres - Part 31: Equipment

dust ignition protection by enclosure “t”

2014 (2013)

The motors have the following markings:

II 3G Ex nA IIB T155°C (T3) Gc X
II 3D Ex tc IIIC T155°C Dc X

Further explanations:
The product is intended solely for installation in an machine. For the product to

be used as intended, the user must comply with the provisions of use and condi-

MSK Motors Operation For Potentially

Explosive Areas

21/27

Appendix

R911323850_Edition 05 Bosch Rexroth AG

Содержание Rexroth MSK030-NSNN Series

















































Результаты поиска

Содержание Rexroth MSK030-NSNN Series

Отзывы:

Похожие инструкции для Rexroth MSK030-NSNN Series

Бренды по названию

Популярные бренды

Bosch Rexroth MSK030-NSNN Series, Руководство по эксплуатации

Результаты поиска

Содержание Rexroth MSK030-NSNN Series

Отзывы:

Похожие инструкции для Rexroth MSK030-NSNN Series

Бренды по названию

Популярные бренды