Bosch rexroth MS2N03-A Скачать руководство пользователя страница 62

Страница: 62 / 72

62 / 72

MS2N

Replace the motor

Bosch Rexroth AG

R911347581, Edition 05

The service lives of motor components, such as

seals and bearings, may vary depending on the

operating conditions, such as operation mode,

speed, vibration and shock load, and frequent

reverse mode. We recommend to change the

bearing after 30,000 operating hours. Shorter

replacement intervals may be necessary; cf.

checks during operation . We recommend reg-

ular visual inspections on shaft sealing rings.

Depending on operating conditions, signs of wear

may appear after 5,000 operating hours. If nec-

essary, replace the shaft sealing rings.
The Bosch Rexroth service helpdesk at our head-

quarters in Lohr, Germany and our worldwide

service provide You can contact us 24/7.

Telephone: +49 (0) 9352 40 50 60
Fax:

+49 (0) 9352 18 49 41

Email

[email protected]

Internet:

⮫

https://www.boschrexroth.com

Preparing information

For quick and efficient help, please have the fol-

lowing information ready:

•

Detailed description of the fault and the cir-

cumstances

•

Information on the rating plate of the prod-

ucts in question, particularly type codes and

serial numbers

•

Your contact data (phone number, fax

number, email address)

Disassembly and

exchange

10.1 Tools required

NOTICE

Motor damage due to strikes onto the motor shaft

−

Do not strike the shaft end and do not

exceed the allowed axial and radial forces

of the motor.

Use suitable tools when disassembling transmis-

sion elements.

Pulling off

Fig. 35: Remove transmission element
Use tools suitable for pulling off. Use a shim to

protect the shaft end when using pulling-off tools.

Heat the output element, if necessary.

10.2 Replace the motor

WARNING

Electric shock due to live parts with more than

50 V!
Replacement may only be performed by per-

sonnel trained and qualified to work on or with

electrical equipment.

Remark:

The motor should be replaced by a

motor of identical type. This is the only way

to ensure that all parameterizations can remain

unchanged.
1.

If necessary, note the previous absolute

value

Open the main switch

Make sure the main switch cannot be

switched back on

Содержание rexroth MS2N03-A









































































Результаты поиска

Содержание rexroth MS2N03-A

Отзывы:

Похожие инструкции для rexroth MS2N03-A

Бренды по названию

Популярные бренды

Bosch rexroth MS2N03-A, Руководство по эксплуатации

Результаты поиска

Содержание rexroth MS2N03-A

Отзывы:

Похожие инструкции для rexroth MS2N03-A

Бренды по названию

Популярные бренды