Bosch Rexroth MAD100 Скачать руководство пользователя страница 44

Страница: 44 / 72

6.3

Connect coolant supply (only for MAF motors)

The inlet (IN) and outlet (OUT) can be arbitrarily assigned. The

assignment does not have any effect on the performance data of

the motor.

MAF ...

Connection via ...

Remark

Thread

Quick coupling

[Ø d

tube]

100 ... 130

G1/4"

9 mm

Select connection according

to type code

160 ... 225

G1/2"

13 mm

Tab. 6-5:

Overview of coolant ports

The connecting threads on the motor are covered with factory-attached pro‐

tective caps. These protective caps must only be removed immediately be‐

fore screwing in the coolant lines or the quick coupling in order to prevent dirt

from entering the cooling system.

Notes for assembly for coolant

ducts

MAF...

Connection

thread

max. screw-in depth

[mm]

Allowed tightening range

[Nm]

100 ... 130

G1/4"

18 ... 20

160 ... 225

G1/2"

27 ... 30

Tab. 6-6:

Cooling connection thread, permissible tightening torques and

screw-in depths

The coolant port threads on the motor may

be destroyed by incorrect tightening torques!

NOTICE

The allowed motor connection tightening torque may not be exceeded! If the

tightening torque or screw-in depth is exceeded, the motor may be damaged

irreversibly.

The coolant connections on the motor side are provided for coolant connec‐

tion threads with axial sealing.
Bosch Rexroth recommends to use threaded connections which contain an

O-ring for axial sealing of the screw connections.
For example, seals consisting of hemp, teflon tape or cone-shaped screw

connections are not considered to be suitable, since this type of seal may

stress the connection thread at the motor to an unreasonably high extent

and/or damage it permanently.

The machine manufacturer is responsible for ensuring that the

coolant connection is tight and for verifying and accepting the

tightness after the motor has been installed.
Additional, regular inspections to ensure proper condition of the

coolant connection should be logged in the maintenance sched‐

ule of the machine.

Quick coupling

It is also possible to use a quick coupling for the coolant port. The quick cou‐

pling features leak protection on either side and can be released even under

full pressure.

30/57

Assembly

MAD / MAF Asynchronous Housing Motors

Bosch Rexroth AG R911336186_Edition 02

Содержание Rexroth MAD100









































































Результаты поиска

Содержание Rexroth MAD100

Отзывы:

Похожие инструкции для Rexroth MAD100

Бренды по названию

Популярные бренды

Bosch Rexroth MAD100, Руководство по эксплуатации

Результаты поиска

Содержание Rexroth MAD100

Отзывы:

Похожие инструкции для Rexroth MAD100

Бренды по названию

Популярные бренды