Bosch Rexroth MAD100 Скачать руководство пользователя страница 43

Страница: 43 / 72

●

The terminal box can only be used for double cabling for

power connection.

●

Fuses F1 (NH...) protecting the wires against overload in

case of a cable break must be dimensioned according to the

current carrying capacity of the particular line cross-section.

●

The fuses should be installed in the control cabinet such that

they are as close as possible to the power output of the con‐

troller.

●

The shield of the motor power cable must be connected to

the control cabinet on the motor side of the fuses such that it

is conducting over a large area.

●

No special power cables are available to establish the dou‐

ble cabling. To install the fuses, standard Rexroth power ca‐

bles have to be opened and cut to the appropriate length on

site.

6.2.4

Connect motor fan (only for MAD motors)

The motor fan is connected to the supply network via a cable and a motor

protective switch and is operated independently of the controller.

①

RLS0782

②

③

④

0,75 … 1,5 mm²
0,75 … 1,5 mm²
0,75 … 1,5 mm²

L1 L2 L3 PE

①

Power connection cable diameter Ø 7 ... 10 mm

②

Protective switch

③

Plug connector

④

Fan

Fig. 6-9:

Fan connection

●

To connect the motor fan, the fan connector must be opened

and closed.

●

The connector for connecting the motor fan is included in the

scope of delivery and is located on the motor fan.

●

Electric connection may only be established by specialized

staff. Observe the safety instructions.

●

The tightness of the connector housing may not be reduced.

●

Motor protective switch and electric fusing are selected by

the machine manufacturer. Please observe the regulations

in the country of installation.

MAD / MAF Asynchronous Housing Motors

29/57

Assembly

R911336186_Edition 02 Bosch Rexroth AG

Содержание Rexroth MAD100









































































Результаты поиска

Содержание Rexroth MAD100

Отзывы:

Похожие инструкции для Rexroth MAD100

Бренды по названию

Популярные бренды

Bosch Rexroth MAD100, Руководство по эксплуатации

Результаты поиска

Содержание Rexroth MAD100

Отзывы:

Похожие инструкции для Rexroth MAD100

Бренды по названию

Популярные бренды