Bosch Rexroth lndraDrive HCS02 Series Скачать руководство пользователя страница 163

Страница: 163 / 382

Description

Symbol

Unit

HMS02.1N-W0028

HMS02.1N-W0054

allowed continuous output current

at f

= 8 kHz; output frequency

out

< f

out_still

out_cont0Hz_

5,1

12,5

allowed continuous output current

at f

= 12 kHz; output frequency

out

< f

out_still

out_cont0Hz_

7,0

allowed continuous output current

at f

= 16 kHz; output frequency

out

< f

out_still

out_cont0Hz_

5,6

assigned output filters at nom. da‐

ta; f

= 4 kHz

also depending on firmware and control section; see Parameter De‐

scription "P‑0‑0001, Switching frequency of the power output stage"; see

"P-0-4058, Amplifier type data"

2) 3)

guide value, see following note

see following note regarding reduction output current

5) 6) 7) 8)

see Parameter Description "P‑0‑0556, Config word of axis controller",

load-depending reduction of PWM frequency fs

Fig.6-64:

HMS - Data of power section - Inverter

Observe that the load is almost independent of the power section

used.
Especially when using standard motors , make sure that they com‐

ply with the occurring voltage load.
Observe the information contained in the chapter “Third-Party Mo‐

tors at IndraDrive Controllers” in the Project Planning Manual of the

drive system.

Depending on the electric output frequency, the output current is

reduced for thermal protection of the power section.
The output current is reduced, when the electric output frequency

has fallen below the threshold to detect motor standstill.

Exemplary Data for Applications

General Information

This chapter contains:
●

examples of allowed current profiles

●

examples of allowed performance profiles

●

data for selecting standard motors

Current Profiles

Current Profile “UEL_I_e”

The following current profiles have been defined for converters and inverters.

Project Planning Manual | Rexroth IndraDrive

Electric Drives

and Controls

| Bosch Rexroth AG 153/369

Power Sections for Inverters - IndraDrive M

Содержание Rexroth lndraDrive HCS02 Series































































































































































































































































































































































































Результаты поиска

Содержание Rexroth lndraDrive HCS02 Series

Отзывы:

Похожие инструкции для Rexroth lndraDrive HCS02 Series

Бренды по названию

Популярные бренды

Bosch Rexroth lndraDrive HCS02 Series, Руководство по планированию проекта

Результаты поиска

Содержание Rexroth lndraDrive HCS02 Series

Отзывы:

Похожие инструкции для Rexroth lndraDrive HCS02 Series

Бренды по названию

Популярные бренды