Bosch Rexroth IndraMotion MTX 11 VRS Скачать руководство пользователя страница 71

Страница: 71 / 304

5.5.3

Deactivating Winlock

Winlock is deactivated when an authorized user logs in.

5.5.4

Closing the User Interface

When an attempt is made to close the user interface, it is checked whether the

logged-in IndraWorks user has the required authorization. If not, the user in‐

terface cannot be closed and a corresponding message window is displayed.

5.6

Overview on Active Corrections

5.6.1

Usage

All correction values used in the NC are displayed in different screens.
The application comprises four screens with the following displays
●

Correction overview 1
–

Zero offsets

–

Tool corrections

●

Correction overview 2
–

Input tools

–

Program coordinates

–

Placements

●

Tool correction register

●

Precision corrections

Integration of the application "Over‐

view on active corrections" in the

operating desktop

The display is assigned to the operating area <OP3> "Machine". Pressing

<F4> "Overview on active corrections" starts the application.
The display is an application with an individual F-key assignment.
The menu and the headline are hidden.

DOK-MTX***-NC*OP***V11-AP01-EN-P
Rexroth IndraMotion MTX 11VRS Standard NC Operation

Bosch Rexroth AG

69/301

General Operation and Visualization

Содержание Rexroth IndraMotion MTX 11 VRS

















































































































































































































































































































Результаты поиска

Содержание Rexroth IndraMotion MTX 11 VRS

Отзывы:

Bosch Rexroth IndraMotion MTX 11 VRS, Руководство по применению, Страница: 71 / 304

Результаты поиска

Содержание Rexroth IndraMotion MTX 11 VRS

Отзывы: