Bosch Rexroth IndraMotion MTX 11 VRS Скачать руководство пользователя страница 69

Страница: 69 / 304

After selection of one of these types the corresponding editor will be started

automatically; it is used to create and edit the file.

Delete

This function deletes the currently selected file. The deleting process has to be

confirmed by the user:
Yes

The file is deleted.

The deleting process is cancelled.

In case of deleting, a multiple selection is possible. In this case, all

selected files are deleted!
Selected, i.e. active NC programs cannot be deleted.

Edit

When operating this function, the data type of the selected file calls the corre‐

sponding editor and loads the selected file.
If the data type of the selected files is not known, the NC program editor is

started in the IndraWorks Operation and a simple ASCII editor is started in the

IndraWorks Engineering. This editor is part of the MTX Navigator.

In case of a multiple selection, files cannot be edited.

Rename

This function renames the currently selected file. After this function has been

activated, a dialog is opened in which the user has to enter the new file name.

The default assignment in the input field is the current file name. The maximum

length of a name is limited to 30 characters. On the mount directory, the max‐

imum length for a file corresponds to the Windows conventions.

Fig.5-42:

dialog "Rename file"

●

With "Ok", the dialog is closed and the file is renamed.

●

By pressing "Cancel" the dialog is closed but the file is not renamed.

●

If you fail to enter a name and press "Ok", an error message is shown.

●

If the name entered already exists in the directory, an error message is

shown.

●

If the file name has more than 30 characters and this file is in the directory

system of the NC kernel, an error message is shown.

●

In case of a multiple file selection, the "Rename" function is

disabled.

●

Selected, i.e. active NC programs may not be renamed.

Copy

With this function, the currently selected file is saved in the clipboard. This

function is required for the function "Insert (File)". Only if an element of the type

"File" is in the clipboard, the function "Insert (File)" is activated and can be se‐

lected by the user.
Every new copying process causes the current content of the clipboard to be

overwritten!

DOK-MTX***-NC*OP***V11-AP01-EN-P
Rexroth IndraMotion MTX 11VRS Standard NC Operation

Bosch Rexroth AG

67/301

General Operation and Visualization

Содержание Rexroth IndraMotion MTX 11 VRS

















































































































































































































































































































Результаты поиска

Содержание Rexroth IndraMotion MTX 11 VRS

Отзывы:

Bosch Rexroth IndraMotion MTX 11 VRS, Руководство по применению, Страница: 69 / 304

Результаты поиска

Содержание Rexroth IndraMotion MTX 11 VRS

Отзывы: