Bosch Rexroth IndraMotion MTX 11 VRS Скачать руководство пользователя страница 52 | Manualshive

Страница: 52 / 304

Bosch Rexroth IndraMotion MTX 11 VRS Скачать руководство пользователя страница 52

Fig.5-23:

System message display

5.3

Two-channel Display

5.3.1

Usage

A display that is vertically divided shows process data and status information

for 2 selected channels.
The display thus allows the user to see 2 channels at once.
One channel is selected as the active channel, reacting to the use of F-and M-

keys.

Integration of the Two-Channel Dis‐

play in IndraWorks Operation

The display is assigned to the operating area <OP3> "Machine". The applica‐

tion is started by pressing <F8 Additional functions> and <F9 Two-channel

display>.
The menu and the headline are hidden.
The display is an application which runs in parallel to the NC screen for a chan‐

nel.
It is possible to switch quickly between single-channel and two-channel display

by pressing <OP3> "Machine".
The functions of the F-keys depend on the NC operating mode and can be

configured in IndraWorks Engineering.

Bosch Rexroth AG

DOK-MTX***-NC*OP***V11-AP01-EN-P

Rexroth IndraMotion MTX 11VRS Standard NC Operation

50/301

General Operation and Visualization

«
...
50
51
52
53
54
...
»

Содержание Rexroth IndraMotion MTX 11 VRS

















































































































































































































































































































Отзывы:

Нет отзывов