Bosch Rexroth IndraMotion MTX 11 VRS Скачать руководство пользователя страница 46 | Manualshive

Страница: 46 / 304

Bosch Rexroth IndraMotion MTX 11 VRS Скачать руководство пользователя страница 46

Fig.5-8:

Program section display

Program symbols

The following table describes the program symbols displayed.

Symbol

Meaning

Note

Line stored Active NC program line

Indicates the NC command line currently

processed by the NC.

Fig.5-9:

Program symbols

Displaying macro contents

If an NC macro was programmed in the NC block, currently hidden contents

can be shown by pausing the NC program, focusing the display and pressing

the <Display macro contents> button. The NC macros are displayed in color.
If the program is continued or the <Hide macro contents> button is confirmed,

the NC macro is hidden again.

To generally show the NC macro contents in the display, you have

to have the authorization for "Display macro contents". Whether the

content of certain NC macros really becomes visible, can be speci‐

fied with read-only rights (technology protection). For additional

information, please refer to the respective documentation.

5.2.6

Program Nesting Display

Display Content

The program nesting display shows the subroutine nesting, including the re‐

trieving of the line numbers and the active NC block.

Fig.5-10:

Program nesting display

Program symbols

The following table describes the program symbols displayed.

Bosch Rexroth AG

DOK-MTX***-NC*OP***V11-AP01-EN-P

Rexroth IndraMotion MTX 11VRS Standard NC Operation

44/301

General Operation and Visualization

«
...
44
45
46
47
48
...
»

Содержание Rexroth IndraMotion MTX 11 VRS

















































































































































































































































































































Отзывы:

Нет отзывов