Bosch Rexroth IndraMotion MTX 11 VRS Скачать руководство пользователя страница 45 | Manualshive

Страница: 45 / 304

Bosch Rexroth IndraMotion MTX 11 VRS Скачать руководство пользователя страница 45

The configuration using the cyclic telegram should be used preferably so that

the service channel is not overloaded unnecessarily.
●

In order to activate the transmission in the cyclic telegram, the SERCOS

configuration files, e.g. "p2ispiXX.scs" (spindle) or "p2icaxXX.scs" (spin‐

dle c-axis) have to be adapted correspondingly.
Thus, the SERCOS parameters S-0-0084 and S-0-0382 have to be im‐

plemented into S-0-0016:

S-0-0016 = (S-0-0084,S-0-0382,...); Torque/force feed-

back value, DC bus power

Within the MTX, S-0-0016 is currently limited to five signals max.
If safety technology is used, five signals might not be sufficient.
In this case, the service channel executes the transfer.

●

Transmission using the service channel is activated automatically by

switching on the spindle display (technology display) in the operation

desktop or by retrieving the movement control services

MCODS(111,...) =>Spindle power

MCODS(110,...) => Spindle torque

active.

The following SERCOS parameters are used to display the spindle torque and

the performance:
●

S-0-0092:
Max. torque (torque/force limit bipolar) in [%].
S-0-0092 generally results from the combination of motor and amplifier

(value in the drive). In the options dialog of the technology display, one

value [in (%)] can be specified for every spindle if this value corresponds

to the full scale deflection of the bar. Thus, an optimum deflection range

can be set for each spindle for the spindle torque bar.

●

S-0-0158:
Max. performance (performance threshold Px) in [W].
The value is to be set valid in the p2-scs files when commissioning the

spindle. S-0-0158 should be set to 1.5 times to the value of the nominal

output.

The spindle service does not provide any values in the c-axis op‐

eration.

If the drive does not support the parameters S-0-0382 or S-0-0084

(e.g. Servodyn-D), a value of 0 is always displayed.

5.2.5

Program Section Display

Display Content

The program section display shows the program section of a running NC pro‐

gram.

DOK-MTX***-NC*OP***V11-AP01-EN-P
Rexroth IndraMotion MTX 11VRS Standard NC Operation

Bosch Rexroth AG

43/301

General Operation and Visualization

«
...
43
44
45
46
47
...
»

Содержание Rexroth IndraMotion MTX 11 VRS

















































































































































































































































































































Отзывы:

Нет отзывов