Bosch Rexroth IndraMotion MTX 11 VRS Скачать руководство пользователя страница 43

Страница: 43 / 304

Fig.5-5:

Coordinate systems

5.2.3

Technology Display

Display Content

The technology display is used to show feed and spindle information. A maxi‐

mum of 8 spindles per channel is supported.

Fig.5-6:

Technology display

Column Selection

The columns and variants are selected using the variant editor of the options

dialog . Variants with the following column data can be defined.
●

Program value

●

Command values

●

Override

●

Maximum override

●

Actual value

●

Gear level

●

Spindle position

●

Spindle power

●

Spindle torque

●

Spindle group

DOK-MTX***-NC*OP***V11-AP01-EN-P
Rexroth IndraMotion MTX 11VRS Standard NC Operation

Bosch Rexroth AG

41/301

General Operation and Visualization

Содержание Rexroth IndraMotion MTX 11 VRS

















































































































































































































































































































Результаты поиска

Содержание Rexroth IndraMotion MTX 11 VRS

Отзывы:

Bosch Rexroth IndraMotion MTX 11 VRS, Руководство по применению, Страница: 43 / 304

Результаты поиска

Содержание Rexroth IndraMotion MTX 11 VRS

Отзывы: