Bosch Rexroth IndraMotion MTX 11 VRS Скачать руководство пользователя страница 40 | Manualshive

Страница: 40 / 304

Bosch Rexroth IndraMotion MTX 11 VRS Скачать руководство пользователя страница 40

5.2

Basic NC Screen

5.2.1

Overview

Different screens with window splits are available for the NC screen of the

Rexroth IndraMotion MTX NC screen. The contents of these partial windows

can be assigned to user-defined displays.
By default, the Bosch Rexroth process displays are located here. These can

be freely configured in the IndraWorks Engineering and adapted to the specific

machine configurations.
The corresponding user rights are necessary for the configuration.
The Bosch Rexroth process displays are provided with machine-dependent as

well as purely interface-related parameters for an individual configuration.
●

Machine parameters are set in the NC configurator in the IndraWorks En‐

gineering.

●

Interface parameters are set in the options dialog of the relevant displays

in the IndraWorks Operation.

You can find further information regarding the configuration of NC

screens in the documentation "Rexroth IndraMotion MTX Commis‐

sioning".

5.2.2

Position Display

Display Content

The position display displays axis data. A maximum of 8 axes per channel is

supported.

Fig.5-2:

Position display

Column Selection

The columns and variants are selected using the variant editor of the options

dialog . Variants with the following column data can be defined.
●

Command position

●

End position

●

Distance to go

●

Program

●

Lag

●

Actual position

●

$ Command position (= channel position during system axis coupling)

●

Command velocity (only ACS)

●

Command speed (only ACS; available only for asynchronous, endlessly

turning round axes, otherwise 0)

Bosch Rexroth AG

DOK-MTX***-NC*OP***V11-AP01-EN-P

Rexroth IndraMotion MTX 11VRS Standard NC Operation

38/301

General Operation and Visualization

«
...
38
39
40
41
42
...
»

Содержание Rexroth IndraMotion MTX 11 VRS

















































































































































































































































































































Отзывы:

Нет отзывов