Bosch Rexroth IndraMotion MTX 11 VRS Скачать руководство пользователя страница 37

Страница: 37 / 304

General Operation and Visualization

5.1

Visualization Symbols

The following table shows and describes the symbols that are displayed.

Meaning

Symbol Explanation

Error

The symbol indicates that an NC error or ProVi error has occurred.

Warning

The symbol indicates that an NC warning or ProVi warning has occurred.

The symbol indicates that, after a change in the configuration system, a system reset

or system restart is required to apply the changes.

The symbol indicates conflicting versions between the interface and NC kernel.

Note

The symbol indicates that an NC note or ProVi note has occurred.

Complete lock

This symbol indicates that the axis output is inhibited for all NC channels.

System waiting mode

This symbol indicates that at least one NC channel is in the waiting state (sum sig‐

nal).

I-Remote

I-Remote inactive

I-Remote active

Winlock

Winlock active

Winlock inactive

Visualization data

This symbol indicates that new visualization data is available that is applied when

restarting IndraWorks Operation.

Connection state
This symbol shows the con‐

nection state between user in‐

terface and control.

Online

Insecure connection

Connection aborted

Communication server (SCP server) failed

DOK-MTX***-NC*OP***V11-AP01-EN-P
Rexroth IndraMotion MTX 11VRS Standard NC Operation

Bosch Rexroth AG

35/301

General Operation and Visualization

Содержание Rexroth IndraMotion MTX 11 VRS

















































































































































































































































































































Результаты поиска

Содержание Rexroth IndraMotion MTX 11 VRS

Отзывы:

Bosch Rexroth IndraMotion MTX 11 VRS, Руководство по применению, Страница: 37 / 304

Результаты поиска

Содержание Rexroth IndraMotion MTX 11 VRS

Отзывы: