Bosch Rexroth IndraMotion MTX 11 VRS Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 304

Bosch Rexroth IndraMotion MTX 11 VRS Скачать руководство пользователя страница 33

The following table contains a description of the message symbols that are

displayed depending on the configuration.

Meaning

Symbol

Explanation

Error

The message indicates an error.

Warning

The message indicates a warning.

Note

The message indicates a note.

Fig.4-12:

Message symbols

Logo Area

Structure and Contents

In addition to the "Rexroth MTX" logo, the logo area contains an animation

started in the waiting state of the interface (e.g. while opening an editor) and

an animation activated when the action recorder starts recording.

Fig.4-13:

Logo area

The NC kernel diagnostic monitor and the system load display can be indicated

via the logo.

NC Kernel: Diagnostic Monitor

The NC kernel diagnostic monitor displays the load distribution of the individual

NC kernel task. Thus, it can be efficiently identified if there is a system overload

due to an incorrect user configuration or programming.
The diagnostic monitor is displayed when double-clicking on the logo.
The "Diagnostic monitor" function can either be linked via a shortcut or a func‐

tion key.
The load distribution of the following tasks is displayed in %:
●

Interpolation and SERCOS (IPO)

●

PLC runtime

●

NC and CPL block processing (SAV/CPL)

●

free capacity (IDLE)

●

Remaining time of all remaining tasks such as the communication, data‐

base accesses, file server (REST).

Fig.4-14:

Diagnostic monitor

The NC kernel diagnostic monitor can negatively influence the run‐

time behavior of the operating machine. Thus, the diagnostic tool

should be switched off after the commissioning. A respective note

is cyclically output in the status line.

DOK-MTX***-NC*OP***V11-AP01-EN-P
Rexroth IndraMotion MTX 11VRS Standard NC Operation

Bosch Rexroth AG

31/301

Operating Elements

«
...
31
32
33
34
35
...
»

Содержание Rexroth IndraMotion MTX 11 VRS

















































































































































































































































































































Отзывы:

Нет отзывов