manualshive.com logo in svg

Bosch Rexroth IndraMotion MTX 11 VRS, Руководство по применению, Страница: 249 / 304

Поделиться
Скачать
Bosch Rexroth IndraMotion MTX 11 VRS Скачать руководство пользователя страница 249

∧ : selected drive is moved one line up
∨: selected drive is moved one line down

Configuration of the Energy Monitor - Auxiliary Equipment

Fig.11-9:

Configuration of the energy monitor - Auxiliary equipment

Within the "Energy Monitor - Auxiliary equipment", the auxiliary equipment has

be be entered as it should appear later on in the display. In contrast to the drives,

the average active power consumption has to be entered in watts for each in‐

dividual auxiliary equipment. The following functions are provided in the win‐

dow:
+: Inserting a new auxiliary equipment
- : Deleting the currently selected auxiliary equipment
∧ : selected auxiliary equipment is moved one line up
∨: selected auxiliary equipment is moved one line down

11.2.3 

Working with the Energy Monitor

Starting the Energy Monitor

Under "Production data", the energy monitor is started via <F2>. The energy

monitor can also be configured in the user screens on F-keys or M-keys.

Total Energy consumption

After calling the energy monitor, the latest ten energy measurements are shown

as bar chart in the main screen. The latest measurement is always shown on

the  right  side.  Each  individual  measurement  shows  the  proportionate  con‐

sumption of the SERCOS drives as well as the entered auxiliary equipment. If

required, the measurement period can be optionally shown with <F2>. This is

especially useful to monitor the production/part manufacturing. Optionally, func‐

tions to execute or suppress energy and time measurements can be configured

via M-keys.

DOK-MTX***-NC*OP***V11-AP01-EN-P 
Rexroth IndraMotion MTX 11VRS Standard NC Operation 

Bosch Rexroth AG

247/301

Extended Functionality

Содержание Rexroth IndraMotion MTX 11 VRS

















































































































































































































































































































Отзывы:

Нет отзывов